517309
46
Zoom out
Zoom in
Previous page
1/78
Next page
schalter des mecablitz in der Position TTL ste-
hen. Im LC-Display (A) wird TTL angezeigt!
Die maximale Reichweite (D) für die gewählte Blen-
de und den Mindestbeleuchtungsabstand (D) kön-
nen Sie im Display des Blitzgerätes ablesen.
Bei geschwenktem Reflektor erfolgt keine Ent-
fernungsanzeige.
Wird der Mindestbeleuchtungsabstand unter-
schritten, so kann es zu Überbelichtungen kom-
men.
Im TTL-Blitzbetrieb muß auch für Versuche auf jeden
Fall ein Stück Film in der Kamera eingelegt sein.
Wollen Sie die Blitzreichweite anhand der
Belichtungs-o.k.-Anzeige (READY) überprüfen, ist
das nur durch Auslösen an der Kamera und nicht mit
dem Handauslöser am Blitz möglich!
Manueller Blitzbetrieb mit voller Lichtleistung
Zum manuellen Betrieb des mecablitz mit voller
Lichtleistung wird der Betriebsartenschalter in
Position M (MANUAL) geschaltet. Im LC-Display (A)
wird M (Manuell) angezeigt. Bei jedem Auslösen des
du mecablitz doit se trouver sur la position TTL.
L'écran ACL affiche TTL (A).
La portée maximale (D) pour l'ouverture choisie et la
portée minimale (D) sont affichées sur l'écran ACL
du flash.
La portée n'est pas affichée lorsque le réflecteur
est basculé. Une distance de prise de vue
inférieure à la portée minimale peut entraîner
une surexposition du sujet.
Pour faire des essais en mesure TTL au flash, il
faut qu’un bout de film soit placé dans le boîtier.
Pour vérifier la portée de l’éclair à l’appui du témoin
de bonne exposition (READY), il faut déclencher
l’éclair au moyen du déclencheur du boîtier et pas
au moyen du bouton de test sur le flash.
Mode manuel à pleine puissance
Pour utiliser le mecablitz en mode manuel à pleine puis-
sance, placez le sélecteur de mode sur la position M
(MANUAL). L'écran ACL (A) affiche M (manuel).A chaque
déclenchement du flash, celui-ci émet un éclair non
dosé correspondant à la pleine puissance lumineuse.
Voor de TTL-flitsfunctie moet de functieschakelaar
van de mecablitz in de stand TTL staan. In het
LC-display (A) wordt "TTL" aangegeven.
De maximale reikwijdte (D) voor de gekozen diafrag-
mawaarde en de minimum flitsafstand (D) kunt u in
het LC-display aflezen.
Bij gezwenkte reflector worden geen afstandden
aangegeven. Als u dichterbij dan de minimu-
mafstand een flits-opname maakt, kan overbe-
lichting optreden.
In de TTL-functie moet ook voor tests altijd een
stuk film in de camera ingelegd zijn.
Wilt u de flitsreikwijdte bepalen aan de hand van de
aanduiding voor belichtings-o.k.(READY) , dan is dat
alleen door ontspannen van de camera mogelijk en
niet door het ontspannen van de flitser!
Met de hand te bedienen instellingen bij flitsen
op vol vermogen
Voor het met handbediening instellen van de flitser
op vol vermogen, moet de functieschakelaar in
de stand M (MANUAL) worden gezet. In het LC-dis-
46
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 40 AF-4 M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 40 AF-4 M in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info