Manual Metabo WEPF 9-125 Quick (page 17 of 124) (All languages)

625650

Zoom out

Zoom in

1/124

ENGLISH en

Use only accessories that

are covered by at least 3.4

mm by the safety guard.

Before carrying out any modifications, remove

the battery pack from the machine and pull the

mains plug from the socket. The machine must be

switched off and the spindle must be at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (5) only

when the spindle is stationary!

- Press in the spindle locking button (5) and turn the

spindle (4) by hand until you feel the spindle

locking button engage.

7.2 Placing the grinding wheel in position

See illustration C on page 2.

- Fit the support flange (3) on the spindle. The

flange should not turn on the spindle when prop-

erly attached.

- Place the grinding wheel on the support flange (3).

The grinding wheel must lay flat on the supporting

flange. The metal flange on the parting grinder

disc must lay flat on the support flange.

7.3 Securing/releasing the (tool-free) clamp-

ing nut (depending on features)

Only tighten the (tool-free) clamping nut (2)

manually.

For the machine to operate, the clip (1) must

always lie flat on

clamping nut (2)

To secure the (tool-free) clamping nut (2):

Do not use the

(tool-free) clamping nut if the

accessory has a clamping shank thicker than 6

! In this case, use the

clamping nut (18) with 2-

hole spanner (19).

- Lock the spindle (see chapter 7.1).

- Flip up the clip

(1)

on the clamping nut.

- Fit the clamping nut (2) on the spindle (4). See

illustration D on page 2.

(1)Tighten the

clamping nut on the clip manually

in a clockwise direction.

- Flip down the clip

(1) again

To release the (tool-free) clamping nut (2)

- Lock the spindle (see chapter 7.1).

- Flip up the clip

(1)

on the clamping nut.

- Unscrew the clamping nut

(2)

, turning it anticlock-

wise manually .

Note:

If the clamping nut is very tightly secured

(2),

you can also use a 2-hole spanner

to unscrew it.

7.4 Tightening/loosening the clamping nut

Securing the clamping nut (18):

The 2 sides of the clamping nut are different. Screw

the clamping nut onto the spindle as follows:

See illustration D on page 2.

- A) For thin grinding wheels:

The edge of the clamping nut (18) faces upwards

so that the thin grinding wheel can be attached

securely.

B) For thick grinding wheels:

The edge of the clamping nut (18) faces down-

wards so that the clamping nut can be attached

securely to the spindle.

- Lock the spindle. Turn the clamping nut (18)

clockwise using the 2-hole spanner (19) to

secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (18) anticlockwise using the 2-hole

spanner (19) to unscrew.

8.1 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid switching on the machine accidentally:

always switch it off when the battery pack is

removed from the machine.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

Machines with slide switch:

Switching on: Push the slide switch (8) forward.

For continuous activation, now tilt down-

wards until it engages.

Switching off: Press the rear end of the slide

switch (8) and release.

7. Attaching the grinding wheel

8. Use

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEPF 9-125 Quick in the language / languages: All languages as an attachment in your email.

The manual is 7,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WEPF 9-125 Quick Manual

Product: