625650

Metabo WEPF 9-125 Quick Manual

16
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISHen
16
4.9 Special safety instructions for cordless
machines:
Remove the battery pack from the machine before
any adjustments, conversions or servicing are
performed.
Protect battery packs from water and mois-
ture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from
defective li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention imme-
diately.
See page 2.
1 Clip to tighten/release the (tool-free) clamping
nut manually *
2 Clamping nut (tool-free) *
3 Support flange
4Spindle
5 Spindle locking button
6 Safety guard
7 Additional handle / Additional handle with vibration
damping *
8 Sliding
on/off switch *
9Handle
10 Switch-on lock *
11 Trigger *
12 Electronic signal indicator
*
13 B
attery pack release button *
14 Capacity indicator button *
15 Capacity and signal indicator *
16 Battery pack*
17 Dust filter
*
18 Clamping nut *
19 2-hole spanner *
20 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
6.1 For mains powered machines only
Before plugging in the device, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
6.2 For cordless machines only
Dust filter
Always fit the dust filter if the surroundings are
heavily polluted (17).
The machine heats up faster when the dust
filter is fitted (17). It is protected by the elec-
tronics system from overheating (see chapter10.).
Attaching:
See page 2, illustration A.
Attach dust filter (17) as shown.
To remove:
Holding the dust filter (17) by the upper
edges, raise it slightly and then pull it downwards
and remove.
Rotating battery pack
See illustration B on page 2.
The rear section of the machine can be rotated 270°
in three stages, thus allowing the machine's shape
to be adapted to the working conditions. Only
operate the machine when it is in an engaged posi-
tion.
Battery pack
Charge the battery pack before use (16).
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
"Li-Power" li-ion battery packs have a capacity and
signal indicator: (15)
- Press the button (14), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the battery pack
To remove:
Press the battery pack release button
(13) and pull the battery pack (16) downwards.
To fit:
Slide in the battery pack (16) until it engages.
6.3 Attaching the additional handle
Always work with the additional handle
attached (7)! Attach the additional handle on
the left or right of the machine and secure.
6.4 Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 11.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See page 2, illustration E.
- Place the safety guard (6) in the position indi-
cated.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Release the lever and turn the safety guard
until the lever engages.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.
5. Overview
6. Initial Operation
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WEPF 9-125 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEPF 9-125 Quick in the language / languages: All languages as an attachment in your email.

The manual is 7,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info