625647

Metabo WEPF 15-150 Quick Manual

18
Zoom out
Zoom in
Previous page
1/112
Next page
ENGLISHen
18
inserted with the machine switched on, or if the
power supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
Use only genuine Metabo accessories.
See page 5.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Safety guard for cut-off grinding
Designed for work with cutting disc and diamond
cutting discs.
Install as described under "Safety guard for
grinding" (chapter 6.2).
B Hand guard for sanding and wire brushing
operations
Designed for work with support plates, sanding
pads, wire brushes.
Install hand guard under the additional side-
mounted handle.
C Dust filter
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
D Multiple position bar for side handle
Permits numerous handle positions.
See www.metabo.com or the catalogue for a
complete range of accessories.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
If the connection lead is damaged, it must be
replaced by a special connection lead.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
The generated grinding dust may contain harmful
substances. Do not dispose with household trash;
dispose of properly at a collection point for
hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with
European Directive 2002/96/EC relating to elec-
trical and electronic waste
and implementation of national law, used electrical
tools must be collected separately and disposed of
in an environmentally friendly manner at recycling
centres.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
Ø = max. diameter of the accessory
t
max,2
= max. permitted thickness of clamping
shank on accessory when using (tool-
free) clamping nut (2)
t
max,3
= roughing disc/cutting disc:
max. permitted thickness of accessory
M=spindle thread
l = length of the grinding spindle
n* = no-load speed (maximum speed)
n
V
* = no-load speed (adjustable)
P
1
=Rated input power
P
2
= Power output
m = Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
* Machines with the designation WE... : Energy-rich,
high-frequency interference can cause fluctuations
in speed. The fluctuations disappear, however, as
soon as the interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, SG
= Vibration emission value
(surface grinding)
a
h, DS
= Vibration emission value
(sanding with sanding plate)
K
h,SG/DS
= Uncertainty (vibration)
Typical A-effective perceived sound levels
:
L
pA
= sound-pressure level
L
WA
= Acoustic power level
K
pA
, K
WA
= Uncertainty
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
11. Accessories
12. Repairs
13. Environmental Protection
14. Technical Data
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WEPF 15-150 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEPF 15-150 Quick in the language / languages: All languages as an attachment in your email.

The manual is 6,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info