Manual Metabo WEPF 15-150 Quick (page 16 of 112) (All languages)

625647

Zoom out

Zoom in

1/112

ENGLISHen

- Ensure good ventilation of the workplace and

keep it clean using a vacuum cleaner. Sweeping

or blowing stirs up dust.

- Vacuum or wash protective clothing. Do not blow,

beat or brush.

See page 2.

1 Clip to tighten/release the (tool-free) clamping

nut manually *

2 Clamping nut (tool-free) *

3 Support flange

4Spindle

5 Spindle locking button

6Safety cover

7 Side handle/Additional handle with vibration

damping *

8 Sliding on/off switch *

9Handle

10 Electronic signal indicator

11 Speed adjustment wheel *

12 Switch-on lock*

13 Trigger switch *

14 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

type plate match your power supply.

Always install an RCD with a maximum trip

current of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle (7)

attached! Attach the additional handle on the

left or right of the machine and secure.

6.2 Attach the safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter 11. Accessories!

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cutting discs.

See illustration C on page 2.

- Place the safety guard (6) in the position

indicated.

- Push the lever (14) and turn the safety guard until

the closed section is facing the operator.

- Release lever and rotate guard

until the lever latches.

- Make sure that the guard is placed securely: The

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least 3.4

mm by the safety guard.

(Disassemble in reverse

order.)

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the cut-off

grinding guard before performing cut-off

grinding work (see Chapter 11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (5) only

when the spindle is stationary.

- Press in the spindle locking button (5) and

turn the spindle (4) by hand until the spindle

locking button engages.

7.2 Placing the grinding wheel in position

See illustration B on page 2.

- Fit the support flange (3) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Place the grinding wheel on the support flange (3).

The grinding wheel must lay flat on the supporting

flange.

7.3 Securing/releasing the (tool-free)

clamping nut

Only tighten the (tool-free) clamping nut (2) by

hand!

For the machine to operate, the clip (1) must

always lie flat on the clamping nut (2).

To secure the (tool-free) clamping nut (2):

Use only accessories which fulfil the

specifications. See Chapter 14. Technical

Data).

- Lock the spindle (see chapter 7.1).

- Flip up the clip (1) on the clamping nut.

- Fit the clamping nut (2) on the spindle (4). See

illustration A on page 2.

- Tighten the clamping nut on the clip (1) manually

in a clockwise direction.

- Flip down the clip (1) again .

Release the (tool-free) clamping nut (2):

- Lock the spindle (see chapter 7.1).

- Flip up the clip (1) on the clamping nut.

- Unscrew the clamping nut (2), turning it

anticlockwise manually .

Note:

If the clamping nut (2) is very tightly secured,

you can also use a 2-hole spanner to unscrew it.

8.1 Adjusting the speed (depending on

features)

Set the recommended speed at the thumbwheel

(11). (small number = low speed; large number =

high speed)

Cutting disc, roughing disc, cup wheel and diamond

cutting disc: high speed

Brush: medium speed

Sanding plate: low to medium speed

5. Overview

6. Commissioning

7. Attaching the grinding wheel

8. Use

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEPF 15-150 Quick in the language / languages: All languages as an attachment in your email.

The manual is 6,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WEPF 15-150 Quick Manual

Product: