665556
14
Zoom out
Zoom in
Previous page
1/104
Next page
ENGLISHen
14
8 Additional handle / Additional handle with vibration
damping *
9 Safety guard for grinding
10 Support flange *
11 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
Before plugging in the device, check to see
that the rated mains voltage and mains
frequency, as specified on the rating label, match
your power supply.
6.1 Attaching the additional handle
Always work with the additional handle
attached (8)! Attach the additional handle on
the left or right of the machine and secure.
6.2 Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 11.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See illustration E on page 2.
- Push and hold the lever (11). Place the safety
guard (9) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
- Press in the spindle locking button (4) and turn the
spindle (2) by hand until you feel the spindle
locking button engage.
7.2 Placing the grinding wheel in position
WBA..., WEBA..., WEPBA...:
See illustration C on page 2.
The Autobalancer support flange (3) is perma-
nently fitted on the spindle. As is the case with
most other angle grinders, a detachable support
flange is not necessary.
The contact surfaces of the Autobalancer
support flange (3), grinding wheel and the
"Quick" clamping nut (1) must be clean. Clean if
necessary.
- Place the grinding wheel on the Autobalancer
support flange (3).
The grinding wheel must lie flat on the Auto-
balancer supporting flange. The metal flange on
the parting grinder discs must lie flat on the Auto-
balancer support flange.
WB 11-125 Quick, WB 11-150 Quick:
See illustration D on page 2.
- Fit the support flange (10) on the spindle. The
flange should not turn on the spindle when prop-
erly attached.
- Place the grinding wheel on the support flange
(10). The grinding wheel must lay flat on the
supporting flange. The metal flange on the parting
grinder disc must lay flat on the support flange.
7.3 Tightening/loosening the "Quick" clamp-
ing nut
Securing the "Quick"clamping nut (1):
Do not use the "Quick" clamping nut
if the acces-
sory has a clamping shank thicker than 8mm
!
- Lock the spindle (see chapter 7.1).
- Position the "Quick"clamping nut (1) on the
spindle (2) so that the 2 lugs engage in the 2
grooves on the spindle. See illustration on page 3.
- Tighten the "Quick"clamping nut by turning clock-
wise by hand.
-Turn the grinding wheel firmly clockwise to tighten
the "Quick"clamping nut.
Releasing the "Quick"clamping nut (1)
:
The "Quick"clamping nut (1) must be attached
before the spindle locking button (4) can hold
the spindle!
- The machine continues to run after switching off.
- Press in the spindle locking button (4) just before
the grinding wheel stops. The "Quick"clamping
nut (1) is released.
8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
6. Initial Operation
7. Attaching the grinding wheel
8. Use
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WBA 11-150 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WBA 11-150 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info