633940
20
Zoom out
Zoom in
Previous page
1/188
Next page
ENGLISH
20
9. Compensate for floor irregularities
with the adjustable base (39).
5.1 Assembly
Riving knife
Note:
The riving knife has been correctly set
at the factory. Readjustment prior to ini-
tial operation is only required should the
riving knife have become misadjusted in
transit.
1. Raise saw blade fully.
2. Turn screw (40) counterclockwise,
raise table insert and remove.
3. Release locking lever (41) (turn
counterclockwise!).
4. Pull riving knife (42) out of lower
transport position upwards as far as
the stop.
5. Checking the riving knife:
Distance between the saw
blade's outer edge and the riving
knife needs to be 3to5mm.
The riving knife must be in align-
ment with the saw blade.
Danger!
The riving knife is one of the safety
devices and must be correctly in-
stalled for safe operation.
Only if realignment of the riving knife
is necessary:
1. Release locking lever (41) (turn
counterclockwise!).
2. Align riving knife (42) vertically:
Distance between the saw blade's
outer edge and the riving knife
needs to be 3 – 5 mm.
3. Tighten locking lever (41) (turn
clockwise!).
Lateral alignment:
riving knife and saw blade (43) must be
in true alignment.
4. Release three Allen screws (44).
5. Align riving knife (43) flush with saw
blade.
.
6. Tighten three Allen screws (44).
7. Secure table insert and lock with
screw (40).
Blade guard installation
1. Raise saw blade fully.
2. Install blade guard (46) on front
mounting on riving knife (45).
3. Firmly tighten blade guard with lock
lever.
5.2 Mains connection
Danger! High voltage
Operate this machine in dry sur-
roundings only.
Operate machine only on a pow-
er source meeting the following
requirements (see also “Techni-
cal Specifications”):
outlets properly installed,
earthed, and tested.
mains voltage and system fre-
quency conform to the voltage
and frequency shown on the
machine´s rating label;
fuse protection by a residual
current operated device (RCD)
of 30 mA sensitivity;
5. Initial Operation
39
40
41
42
max. 5
45 46
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TS 254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TS 254 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info