816557

Metabo STA 18 LTX 150 BL Manual

12
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISHen
12
7.2 Insert saw blade Fig. B
Use a saw blade that is suitable for the material
being sawn.
- Turn the clamping lever (23) forwards to the stop
and hold in place.
- Insert the saw blade (20) against the spring force
until the stop. (The saw teeth are facing forwards).
Ensure that the blade is correctly positioned in the
groove of the saw blade support roller (21).
- Release the clamping lever (23). (It returns to its
initial position by itself. The saw blade is now
securely tightened).
7.3 Removing the saw blade
Caution: Be careful not to point the jigsaw at
anyone when removing it.
- Turn the clamping lever (23) forward until the stop;
the saw blade is ejected as a result of spring force.
7.4 Attaching / removing the protective cap
Fig. A
Attachment: Slightly press together the protective
cap (5) and push on at the front until the stop
(see fig. A p. 2).
Removal: Grip both sides of the protective cap (5),
then pull forwards and remove.
7.5 Sawing with dust extraction Fig. A
- Fit the extractor connection piece (16). Connect a
suitable extraction device.
- Attach the protective cap (5) for maximum
extraction efficiency.
7.6 Sawing without dust extraction
- Work with the protective cap (5) removed (see
Removal chapter 7.4).
7.7 Diagonal cuts Fig. C
Remove the protective cap (5), the protective plate
(2), anti-splintering footplate (3) and extraction
connection piece (16). These parts cannot be used
for diagonal cuts.
- Slacken the screw (25).
- Slide the footplate (17) back slightly and turn.
- You can read off the angles from the scale (24).
Adjust to different angles using an angle gage.
- Push the footplate (17) forward in the angles
provided until it engages.
- Tighten the screw (25).
7.8 Battery pack
Charge the battery pack (14) before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
In case of Li-Ion battery packs with capacity and
signal display (13) (equipment-specific):
- Press the button (12); the LEDs indicate the
charge (13) level.
- If one LED is flashing (13), the battery pack is
almost empty and must be recharged.
7.9 Removing and inserting the battery pack
Fig. A
Removing: Press the battery pack release button
(15) and pull the battery pack (14) upwards.
Inserting: Slide in battery pack (14) until it locks.
8.1 Setting the pendulum motion Fig. A
Set the required pendulum motion using the
adjustment lever (7).
Position "0" = pendulum motion is switched off
. . .
Position "III" = maximum pendulum motion
Recommended settings: P. 4
The best way to determine the ideal setting is
through a practical trial.
8.2 Setting the maximum stroke Fig. A
Set the machine to maximum speed using the
setting wheel (11). This can also be done during
operation.
Recommended settings: P. 4
The best way to determine the ideal setting is
through a practical trial.
8.3 Switching On/Off, continuous operation
Fig. A
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off and keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handle provided, stand
securely and concentrate.
STA 18 LTX 150 BL 601502000
Switching on: Push the slide switch left or right (19)
forwards. The device runs continuously.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handle provided, stand
securely and concentrate.
Switching off: Push the slide switch (19) forwards.
STAB 18 LTX 150 BL 601503000
Switching on: press the trigger switch (10). Press
the trigger more to increase the speed (up to preset
maximum speed, see chapter 8.2).
Switching off: Release the trigger switch (10).
Continuous operation: For continuous operation,
the pressed trigger (10) can be locked using the
lock button (9). Press the trigger switch (10) again to
stop the machine.
8. Use
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo STA 18 LTX 150 BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo STA 18 LTX 150 BL in the language / languages: All languages as an attachment in your email.

The manual is 4.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info