599612
11
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH en
11
7.8 Tool change with a geared chuck (10)
(equipment-dependent)
See illustrations, page 3.
Clamping tool:
Insert the tool and use the chuck key (11) to
uniformly clamp tight in all 3 bores.
Removing tool:
Open the geared chuck (10) with chuck key (11)
and remove tool.
7.9 Removing the chuck
Undo the locking screw. Caution left-handed
thread!
Hold the drill spindle firmly with an open-ended
spanner. With a light blow from a rubber hammer,
release the chuck from the clamped hexagon
spanner and unscrew it.
Keyless chuck cleaning:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close it
several times. The dust collected falls from the
opening. Regular use of cleaning spray on the jaws
and jaw openings is recommended.
f
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
See page 4.
A Angle drilling and screwdriving attachment
BFlexible shaft
CDrill stand
DMachine vice
E Scaffolding hook with integrated bit depot:
Clip into the
scaffolding hook fastening (6)
and
turn to engage in one of the 4 positions.
F Steel wire end brush
G Steel wire cup brush
H Steel wire rotary brush
I Bit clamping bush
For complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric
equipment and its implementation in national legal
systems, used power tools must be collected
separately and handed in for environmentally
compatible recycling.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
=Nominal power input
P
2
=Power output
n
0
=No load speed
n
1
=Speed at rated load
s max. =Max. impact rate
ø max. =Max. solid drill diameter
b =Chuck capacity
G =Drill spindle thread
H =Drill spindle with hexagon socket
m =Weight without mains cable
D =Collar diameter
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the emis-
sions from this power tool and compare these with
the values emitted by other power tools. The actual
values may be higher or lower, depending on the
particular application and the condition of the tool or
8. Maintenance
9. Accessories
10. Repairs
11. Environmental Protection
12. Technical Specifications
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SBE 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SBE 610 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info