600619

Metabo RS 17-125 Manual

12
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISHen
12
To remove:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (7) anticlockwise using the 2-hole
spanner (6) to unscrew.
8.1 Working close to walls
To open and close the segment: switch off the
machine and pull the mains plug. The acces-
sory must be stationary.
Only raise the segment (13) when working
close to walls. Otherwise, the segment must
be lowered.
The open area of the safety guard must face the
direction of the wall.
8.2 Setting the speed (RS 14-125)
Set the optimum speed on the setting wheel (20),
depending on the application.
A wheel setting of between 4 and 6 is suitable for
most applications.
8.3 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only set it
down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate on the work.
RS 14-125:
Switching on:
Push the slide switch (18) forward.
For continuous activation, now tilt down-
wards until it engages.
Switching off:
Press the rear end of the slide switch
(18) and release.
RS 17-125:
Momentary activation
Switching on:
Press in lock (16) and then press
trigger (17). Release the lock (16).
Switching off:
Release the trigger (17).
Continuous operation:
Switching on:
Press in lock (16) and hold in. Press
and hold in trigger (17). The machine is now
switched on. Now release the trigger (17).
Then release the lock (16) to hold the trigger
in position and prevent deactivation
(continuous operation).
Switching off:
Press the trigger (17) and release.
Motor cleaning: The machine must be vacuumed
regularly, frequently and thoroughly through the
ventilation slots using a suitable vacuum cleaner.
The machine must be held firmly in this case.
Replacing the spring-mounted ring brush:
Replace worn brushes for optimal dust extraction.
Replacement brush set: Order No. 6.28214.
RS 14-125:
The electronic signal display (19) lights
up and the load speed decreases. The coil
temperature is too high! Run the machine in
idling mode until the electronics signal indicator
switches off.
The electronic signal display (19) flashes
and the machine does not start. The restart
protection is active. If the mains plug is
inserted with the machine switched on, or if the
current supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
RS 17-125:
- Restart protection: If the mains plug is inserted
with the machine switched on, or if the current
supply is restored following an interruption, the
machine does not start up. Switch the machine off
and on again.
- Overload protection: There is a reduction in
load speed. The coil temperature is too high!
Allow the machine to run at idle speed until it has
cooled down.
- Switching on the machine reduces the voltage
briefly. Unfavourable mains power conditions may
have a detrimental effect on other machines.
Network impedances less than 0.4 ohms should
not cause malfunctions.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
8. Use
9. Cleaning, Maintenance
10. Troubleshooting
11. Accessories
12. Repairs
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo RS 17-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo RS 17-125 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info