600619
11
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISH en
11
- The workplace must be well ventilated.
- The use of a dust mask of filter class P2 is recom-
mended.
Follow national requirements for the materials you
want to work with.
Material containing asbestos must only be treated
by specialists.
When working in dusty conditions, ensure that
ventilation openings are not blocked. If it becomes
necessary to remove dust, first disconnect the
power tool from the mains supply (use non-metallic
objects) and avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Connect a FI circuit-breaker with max.
release current (30 mA) upstream when using the
machine outdoors.
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked auxiliary handle must be
replaced. Never operate a machine with a defective
auxiliary handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Only use accessories that are surmounted by
brushes of the safety guard.
See page 2.
1 Extractor connection piece
2 Threaded holes on gear housing (both sides)
3Thumb screws
4 Auxiliary handle
5Locking discs
62-hole spanner
7Adjusting nut
8Diamond cup wheel*
9Support flange
10 Spindle
11 Spring-mounted ring brush
12 Spindle locking button
13 Opening segment (for working close to walls)
14 Safety guard
15 Handle
16 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
17 Trigger (for switching on and off)
18 Slide switch (for
switching on/off) *
19 Electronic signal indicator
20 Speed adjustment wheel
* depending on equipment/not in scope of delivery
Before plugging in the machine, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual
current of 30 mA or less.
6.1 Attaching the auxiliary handle
Always work with the auxiliary handle attached
(4)! Attach the auxiliary handle as shown.
See illustration A on page 2.
- Fit locking discs (5) to the left and right of the gear
housing.
- Fit the auxiliary handle (4) on the gear housing.
- Insert the thumb screws (3) to the left and right of
the auxiliary handle (4) and turn gently.
- Adjust the auxiliary handle to the required angle
(4).
- Manually tighten the thumb screws (3) to the left
and right.
6.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (1).
For optimal dust extraction, use the connecting
sleeve 6.30796.
We recommend using an antistatic suction hose
with diameter 35 mm.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle must be at a standstill.
7.1 Locking the spindle
Press in the spindle locking knob (12) only
when the spindle is stationary!
- Press in the spindle locking button (12) and turn
the
spindle (10) by hand until you feel the spindle
locking button engage.
7.2 Fitting/removing the diamond cup wheel
See illustration B on page 2.
To fit:
- Fit the support flange (9) on the spindle. (10) The
flange should not turn on the spindle when prop-
erly attached.
- Lay the diamond cup wheel (8) on the support
flange (9) so that it lies flat along the support
flange.
- The two sides of the clamping nut (7) are different.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (7) is facing upward.
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (7) clockwise using the 2-hole
spanner (6) to secure.
5. Overview
6. Initial Operation
7. Attaching the accessory
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo RS 17-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo RS 17-125 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info