595156
51
Zoom out
Zoom in
Previous page
1/76
Next page
51
Milling profiles
When working with profile router bits, first make a coarse cut and then a fine cut.
The forward speed should not be too slow, otherwise the wood will burn and the router bit become
blunt too quickly.
Profilage à la fraise
En cas de travail avec des fraises à profiler, enlever d’abord un grand copeau, puis un plus petit.
L’avance ne doit pas être trop faible, le bois risque sinon de griller et la fraise de s’émousser
prématurément.
Profilfräsen
Beim Arbeiten mit Profilfräsern zuerst einen größeren Span und anschließend einen kleineren Span
abnehmen.
Der Vorschub darf dabei nicht zu gering sein, da sonst das Holz versengt und der Fräser vorzeitig
stumpf wird.
Profielfrezen
Bij het werken met profielfrezen eerst een grote spaan en daarna een kleinere spaan afnemen.
De frees mag daarbij niet te langzaam naar voren bewogen worden, omdat anders het hout verschroeit
en de frees vroegtijdig bot wordt.
Uso delle frese sagomate
Lavorando con frese sagomate, prelevare prima un truciolo di maggiori dimensioni, poi un truciolo
minore.
L'avanzamento non dovrà essere troppo lento: altrimenti il legno si brucia e la fresa si ottunde
prematuramente.
Fresado de perfiles
Cuando se trabaje con fresas perfiladoras, fresar primeramente una astilla espesa y después otra más
fina.
El avance en este caso no debe de ser demasiado escaso, de lo contrario la madera se chamusca y la
fresa se desafila prematuramente.
Fresagem de perfis
Ao trabalhar com fresas de perfilar, cortar primeiro uma apara maior e depois uma apara mais
pequena.
O avanço não deve ser lento demais, de modo a evitar que a madeira seja chamuscada e a fresa
embotada prematuramente.
Profilfräsning
Under arbetet med profilfräsar avverka först ett större spån och sedan ett mindre spån.
Frammatningen får inte vara för liten eftersom annars trät sveds och fräsen slöas för tidigt.
Profiilijyrsintä
Käytettäessä profiilijyrsimiä jyrsitään ensin isompia lastuja ja sitten pienempiä lastuja.
Syötön ei pitäisi olla liian pieni, koska muuten saattaa puu kärventyä tai jyrsin tylstyä.
Profilfresing
Ved arbeid med profilfres tas det først av et større spon og deretter et mindre spon.
Fremføringen må ikke være for liten, ellers blir treet svidd og fresen for tidlig sløv.
Profilfræsning
Ved arbejdet med profilfræsere aftages der først en større spån og bagefter en mindre spån.
Derved må fremføringen ikke være for lille, ellers bliver træet svedet og fræseren bliver sløv før tiden.
Frezowanie profilowe
W czasie czynności frezowania profilowego należy rozpocząć od usuwania większego wióra,
zakończyć zaś zdejmowaniem mniejszego wióra. Szybkość przesuwania frezarki nie może być zbyt
niska, aby nie dopuścić do pogrążenia frezu i przedwczesnego stępienia jego krawędzi tnących.
Profilmarás
Profilmaróval történő munkavégzésnél először egy nagyobb fogást, majd egy kisebb fogást szedjen le.
Eközben az előtolás nem lehet túl kicsi, mert különben a fa megperzselődik és a marószerszám idő
előtt életlenné válik.
Φρέζάρισμα προφίλ
Κατά την εκτέλεση εργασιών µε φρέζεσ προφίλ φρεζάρετε έτσι, ώστε να προκύπτουν πρώτα
χοντρά πριονίδια και κατπιν πιο λεπτά.
Η προώθηση µωσ δεν επιτρέπεται να είναι ελάχιστη, διτι προκαλούνται εγκαύµατα στο ξύλο
και η φρέζα στοµώνει πρωρα.
OfE_1229_Signal_0112_Teil2.qxp:OfE_1229_Signal_0508_Teil2.qxp 27.02.2013 16:59 Uhr Se
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo OF E 1229 SIGNAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo OF E 1229 SIGNAL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info