451464

Metabo Multi 310G Manual

25
Zoom out
Zoom in
Previous page
1/64
Next page
25
ENGLISH
Cutting speed in m/s
Danger!
At this combination there is an
increased risk of kickback and/or tool
breakage.
The speed is set by changing a belt:
• upper pulleys:
speed of cutter spindle 8500 min
-1
• centre pulleys:
speed of cutter spindle 6750 min
-1
• lower pulleys:
speed of cutter spindle 4300 min
-1
1. Open the spindle drive guard (push
guard hood (55) to bottom).
2. Loosen lock lever (56) and slacken
belt by pushing the lever (57)
towards the cutter spindle.
3. Shift belt to desired pulleys.
Danger!
The belt must always run on
pulleys that are level with each other.
4. Tighten belt by pulling the lever (57)
away from the cutter spindle.
5. Lock motor in position with the lock
lever (56).
6. Close the guard hood. The set
speed is displayed on the outside on
the guard hood.
Work area preparation
Ensure the removal of all not required
objects from the work area:
1. Saw blade and blade guard fully
retracted and covered by table
insert?
2. Fence removed?
3. Morticing bit chuck covered?
Cutter installation
1. Remove table insert and table insert
rings.
2. Loosen locking screw (58) and
crank cutter spindle with handwheel
(59) fully up.
3. To block the cutter spindle, push on
lock pin (60) – turn cutter spindle by
hand until the lock pin engages.
4. Loosen spindle nut (61) and remove
any fitted cutters and spacing col-
lars.
5. Fit new cutter and spacing collars on
the cutter spindle.
Caution!
− Observe direction of rotation of
the cutter (counter-clockwise if
viewed from top)!
− The cutter must be positioned on
the cutter spindle as far down
possible!
6. Cover the clearance zone around
the cutter spindle with table insert
rings that accommodate the cutter
head diameter.
7. Fill space between cutter and spin-
dle thread with spacing collars.
8. Tighten spindle nut, with the open
end wrench supplied, hand-tight
only.
Danger!
− Do not extend open end wrench
for tightening the spindle nut.
− Do not tighten spindle nut by stri-
king the wrench.
− Pull lock pin (60) fully out.
9. Rotate cutter spindle by hand to
see that it runs clear of the table
insert rings.
10. Crank cutter spindle fully down with
handwheel (59).
Cutter fence installation
1. Install the cutter fence's base first.
To do so, screw both bolts (62) into
the tapped holes in the machine
table.
2. Fasten the articulated arm (63) with
two each hexagon socket head cap
screw and washer to the rear of the
cutter fence's base.
3. Slide the hexagonal extension arm
(64) into the relevant bracket on the
articulated arm (63) and tighten.
4. Slide vertical holddown shoe (65)
onto the extension arm and tighten.
5. Slide lateral pressure shoe (66) onto
extension arm and tighten.
6. Connect a suitable dust collector to
the cutter fence's base.
Tenoning guard plate installation
1. Slide guard plate (67) into the
groove in the sliding carriage (68),
right up against the mitre fence and
tighten both screws on the rear of
the guard plate.
Tool
∅
Cutter spindle-
speed (min
–1
)
4300 6750 8500
180
40 m/s 64 m/s
160
57 m/s 71 m/s
140
50 m/s 63 m/s
120
43 m/s 54 m/s
100

45 m/s
55
57 56
58
59
60
61
62
63
6465
66
67 68
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 310G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 310G in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 4,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info