451464

Metabo Multi 310G Manual

23
Zoom out
Zoom in
Previous page
1/64
Next page
23
ENGLISH
7. Feed workpiece slowly and straight
into the thicknesser. It will then be
automatically fed through the thick-
nesser.
8. Guide workpiece straight through
the thicknesser.
To remove the workpiece from the
machine, position yourself offset to
one side of the outfeed opening.
9. Switch machine off if no further plan-
ing is to be done immediately after-
wards.
Workpiece dimensions
• Length: min. 200 mm.
• Width: max. 309 mm.
• Thickness: min 5 mm;
max. 200 mm.
Tips and Tricks
• Plane stock with the grain, if possi-
ble.
• Use roller supports on both sides of
the planer/thicknesser when work-
ing long stock.
• When thickness planing it is better
to make several passes with little
chip removal, than making only few
passes with a high depth of cut.
• Keep surfaces of planing beds clean
– in particular, remove resin residue
with a suitable cleaning and mainte-
nance spray (optional accessory).
• Apply an anti-seize compound (for
example WAXILIT) to all planing
bed surfaces afterwards. This
makes feeding easier and provides
for a smoother surface finish.
8.1 Setup
Danger!
Before setting the machine up:
− Switch machine OFF.
− Unplug.
− Wait until machine has come to a
complete stop.
Work area preparation
Ensure the removal of all not required
objects from the work area:
1. Cutter fence completely dis-
mounted?
2. Cutter spindle fully retracted and
covered by table rings and insert?
3. Cutterblock cover lowered on the
table?
4. Morticing bit chuck covered?
Raising the saw blade
1. Remove table insert.
2. To raise the saw blade, turn blade
guard lever (36) counter-clockwise,
push down and tighten again by
turning clockwise.
Replace the kerf plate. To do so, slightly
bend the table insert apart at its rear and
slide over saw blade and riving knife.
Then fit table insert flush into the saw
table.
Rip fence installation
1. Place the fence carrier (37) on the
guide bar (38) and secure with the
star-knob screw (39).
2. Cover cutterblock with the cover
plate (40).
Sliding carriage side extension instal-
lation
1. Fit strut (41) as illustrated into seat
of extension arm (42) and table
bracket (43).
2. Fit table (45) into groove of sliding
carriage and secure at both ends
with a clamping plate (46).
3. Adjust height with the regulating
screw (44) in the strut.
Mitre fence installation
The mitre fence can be used both in
front of or behind the workpiece.
• When used in front of the
workpiece –
especially suitable for cutting ledges
and boards:
8. Operation as Table Saw
36
37
3938
40
41
42
43
44
45
46
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 310G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 310G in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 4,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info