451464

Metabo Multi 310G Manual

19
Zoom out
Zoom in
Previous page
1/64
Next page
19
ENGLISH
always work with a properly set riving
knife.
Do not jam workpieces.
Cut thin or thin-walled workpieces only
with fine-toothed saw blades. Always
use sharp saw blades.
If in doubt, check workpiece for inclusion
of foreign matter (e.g. nails or screws).
Drawing-in/trapping hazard!
Ensure that no parts of the body or cloth-
ing can be caught and drawn in by rotat-
ing components (no neckties, no loose-
fitting clothes; contain long hair with hair-
net).
Hazard generated by insuffi-
cient personal protection gear!
Wear hearing protection.
Wear safety glasses.
Wear dust mask if work generates dust.
Wear suitable work clothes. When work-
ing outdoors wearing of non-slip shoes is
recommended.
Risk of injury by inhaling wood
dust:
Dust of certain timber species (e.g. oak,
beech, ash) can cause cancer when
inhaled: Always use a dust collector. The
dust collector must meet the following
requirements:
− fitting the outer diameter of the suc-
tion port
− air volume ≥ 550 m
3
/h;
− vacuum at suction port of machine
≥ 740 Pa;
− air speed at suction port of machine
≥ 20 m/s.
Hazard generated by modifica-
tion of the machine or use of parts
not tested and approved by the equip-
ment manufacturer!
Assemble electric tool in strict accord-
ance with these instructions.
Use only parts approved by the equip-
ment manufacturer.
Do not make changes to any of the
parts.
Use only cutting tools according to
EN 847-1.
Use only matching saw blades and riving
knives.
Hazard generated by electric
tool defects!
Keep electric tool and accessories in
good repair. Observe the maintenance
instructions.
Check electric tool for possible damage
before any use: Before operating the
electric tool all safety devices, protection
devices or slightly damaged parts must
be inspected for proper functioning as
specified. Check to see that all moving
parts work properly and do not jam. All
parts must be correctly installed and
meet all conditions necessary for the
proper operation of the electric tool.
Damaged protection devices or parts
must be repaired or replaced by an
qualified specialist. Have damaged
switches replaced by a service centre.
Do not operate electric tool if the switch
can not be turned ON or OFF.
Keep handles free of oil and grease.
2.3 Symbols Used Through-
out These Instructions
Danger!
Indicates risk of personal
injury or severe material
damage.
Risk of electric shock!
Risk of personal injury by elec-
tric shock.
Danger! Drawing-in/trapping
hazard!
Risk of personal injury by body
parts or clothing being drawn
into the rotating saw blade.
Caution!
Risk of material damage
Note:
Supplementary information
• One machine – four operating
modes:
− surface planer
− thicknesser
− circular saw
− spindle moulder
• Wide range of accessories.
• Latest technology for perfect per-
formance.
4.1 Machine installation
1. Transport combination machine on
the pallet to a suitable location:
− Floor space required
at least 3 m x 4 m.
Depending on workpiece dimen-
sions the required space may be
more.
− sufficient load bearing capacity
− level
− even
− dry
− non-slip.
2. Remove packing and enclosed
parts.
3. Unscrew and remove the metal
clamps holding the combination
machine on the pallet.
4. Lead carrying straps though under-
neath the combination machine at
the marked locations (1).
5. Lift combination machine off the pal-
let.
Danger!
The combination machine can
turn over while being carried! Take
care to keep the machine balanced
while carrying it.
Caution!
Lift the machine only at the
locations mentioned in this manual.
Other components are not designed
for the tensile load by the machine
weight.
4.2 Mains Connection
Danger! Electrical hazard.
Operate in dry environment
only.
Operate machine only on a power
source matching the following
requirements (see also "Technical
Specifications"):
− protected by a residual current
operated device of 30 mA capa-
city;
− outlets properly earthed;
− 5-wire three-phase outlets with
neutral lead.
− when a dust collector is used it
must also be properly earthed.
Position power supply cable so it
does not interfere with the work and
is not damaged.
Protect power supply cable from
heat, aggressive liquids and sharp
edges.
Use only extension cables of suffi-
cient lead cross-section.
Do not pull on power supply cable to
unplug.
Check direction of rotation!
(machines with 3-phase motor
only):
Depending on the phase sequence it
is possible that the motorshaft will
turn in reverse rotation. This can
cause damage to the machine and
workpiece. It is therefore necessary
to check the direction of rotation after
each connection to a different power
3. Special Product Features
4. Transportation and
Installation
1
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 310G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 310G in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 4,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info