600596

Metabo LSV 5-225 COMFORT Manual

11
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH en
11
Pull the plug out of the plug socket before any
servicing or cleaning are performed.
Regularly check the support plate (1). Replace
worn support plate (1)
1. Remove the locking screw (18) of the support
plate.
2. Remove support plate (1) and washer (19).
3. Refer to the Accessories chapter for
replacement support plates with velcro-type
fastening.
4. Mount support plate (1) and rotate until it
engages on carrier disc.
5. Re-insert fixing screw (18), together with washer
(19) and tighten.
Regularly check the backing pad (3). Replace
worn backing pad (3)
See page 2, fig. D.
- Pull out brush rim (3).
- Insert new brush rim (order no. 6.26663).
Regularly check the rubber lip (4). Replace
worn rubber lip (4)
See page 2, fig. D.
- Dismantle support plate (1).
- Unscrew fixing screws of the rubber lip (4).
- Mount new rubber lip (order no. 3.44101740).
Replace worn shaft (22)
see fig. , page 3.
Removal:
1. Press pushbutton (e.g. With Allen key) and keep
pressed.
2. Remove shaft.
3. Unscrew the shaft from the sanding head (right-
hand thread)
Fitting:
- Ensure that the shaft core does not fall out from
the shaft tube when fitting and gets dirty.
1. Screw new shaft (order no.: 6.26664) into the
sanding head until the stop, but do not tighten
yet.
2. Bend the “shaft end with pushbutton” towards
the handle bar. Unscrew the shaft end at the
sanding head again until the “shaft end with
pushbutton” can be inserted in the handle bar
and the pushbutton engages (if required turn the
sanding plate slightly by hand to make the
insertion of the shaft easier.)
LSV 5-225 Comfort (only if required):
Readjust tension of the handle bar connection
See page 2, fig. E.
1. Lift locking bow (6)
2. Swivel the hook holder (7) downwards.
3. Slacken the screw (20).
4. Turn eccentric (21) by one stop.
+ = increase tension
– = reduce tension
5. Tighten the screw (20) again.
6. Repeat step 3 -5 also on the opposite side.
7. Fix handle bar (8) and check tension.
8. If needed, repeat steps 1-7 and, if required, also
turn the eccentric in tht other rotational direction.
Use only genuine Metabo accessories.
Note:
Note: Metabo accessories are adapted to suit
the machine's velcro-type fastening. This increases
the service life of the velcro-type fastening.
A Support plate with velcro-type fastening (soft,
as replacement): Order no.: 6.26661
B Support plate with velcro-type fastening (hard):
Order no.: 6.26662
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D = Diameter of support plate
P
1
=Rated input power
P
2
= Power output
n
0
=No-load speed
n
1
= Speed at rated load
m = weight (without mains cable, without
sanding plate, for LSV 5-225 Comfort in
length of 1.6 m).
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ AC Power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
9. Maintenance 10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo LSV 5-225 COMFORT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo LSV 5-225 COMFORT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info