600596

Metabo LSV 5-225 COMFORT Manual

10
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISHen
10
15 Sanding head
16 Service flaps
17 Screws of the service flaps
18 Locking screw for support plate
19 Washer
20 Screw of the eccentric
21 Eccentric
22 Shaft
* depending on the model / features
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
6.1 Shorten or extend handle bar (LSV 5-
225 Comfort)
Disassemble handle bar
See figure A.
1. Lift locking bow (6)
2. Swivel the hook holder (7) downwards.
3. Pull apart the handle bars (8).
See figure A.
Assemble handle bars
See figure B.
1. Put together (8) the handle bars as shown.
2. Swivel the hook holder upwards (7) until the
stop.
3. Fold the locking bow (6) downwards until it
touches the handle bar.
4. Check for secure connection. If the handle bars
cannot be connected securely, the tension has
to be adjusted. See chapter maintenance.
6.2 Installation of sanding sheet
Sanding sheet with velcro-type fastening
Simple attachment and removal thanks to the
velcro-type fastening. Simply press on the sanding
sheet so that the holes in the sanding sheet (2) are
aligned with the support plate (1).
6.3 Dust extraction
To optimise the dust extraction performance, fit the
sanding sheet (2) so that the holes on the sanding
sheet are aligned to the support plate (1).
For optimum vacuum power turn the brush rim as
shown (until the stop): Brush rim (3) and rubber lip
(4) completely encompass the support plate (1) .
Connect a suitable extraction device to the extractor
connection piece (14).
When sanding prepared surfaces with high dust
generation we recommend using an all-purpose
vacuum cleaner with automatic filter cleaning for
continuous use (e.g. ASR 35 L ACP, ASR 35 M
ACP).
Note: the bush 316062390 is particularly suited as
it is secured against slipping with a bayonet closure.
Fix the bush 316062390 to the extraction hose as
follows: Remove the bush of the suction hose from
the suction hose (left-hand thread) and fix special
bush (left-hand thread).
6.4 Sanding near edges
When sanding near edges turn the brush rim (3) in
such a way that the support edge (5) can be guided
along the workpiece edge.
Use only in assembled state. Do not switch on
the machine if tool parts are missing or
defective.
7.1 Switching on/off of the machine
Switch the machine on/off at the switch (11) .
I=On
0=Off
First switch on the machine and then bring the
sanding plate to the work surface.
If the requirements for the quality of the sanding
result are very high, we recomment to first bring the
sanding plate to the work surface and then switch
on the machine.
7.2 Setting speed
Set the speed at the setting wheel (12). This can
also be done during operation.
The best way to determine the ideal setting is
through a practical trial.
7.3 Switching on / off of the LED light
Use the switch (10) to switch the LED ligth (9) on or
off.
(The LED light is on only when the motor is running.)
I=On
0=Off
Pull the plug out of the plug socket before any
servicing or cleaning are performed.
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Clean the support plate (1) as required (vacuum
off the dust). This increases the service life of the
velcro-type fastening.
Remove blockages in the sanding head (15)
-Note:
left and right cleaning flap (16) are not
interchangeable, therefore do not interchange!
Remove fixing screws of the service flaps (17),
remove service flaps and put aside.
- Vacuum with the crevice nozzle of an extraction
device, if required, ensure clear passage using a
wire.
- If required, remove support plate (1) and vacuum
the extraction channels underneath and ensure
clear passage.
6. Commissioning
7. Use
8. Cleaning
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo LSV 5-225 COMFORT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo LSV 5-225 COMFORT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info