599620

Metabo LF 724 S Manual

11
Zoom out
Zoom in
Previous page
1/80
Next page
ENGLISH en
11
Set the desired cutting depth by turning the setting
screw using a hexagonal wrench (9-a).
Possible cutting depths: 0-0.3 mm
Start with a small cutting depth and increase it
gradually until you have reached the optimum
setting for the workpiece to be processed.
Do not leave the hexagonal wrench in
place!
7.4 Attaching / Removing the extraction
connection piece
Use a Metabo all-purpose vacuum cleaner for dust
extraction purposes.
Attachment
Push the extraction connection piece (7) until it
engages into the extraction nozzle (6).
Now the desired extraction unit can be connected to
the extraction connection piece with the pipe
diameter 35 mm.
Removal
Press the lip and simultaneously remove the
extraction connection piece (7) from the extraction
nozzle (6).
8.1 Guiding the paint remover
Always use two hands to guide the paint remover
backwards where possible over the surface of the
workpiece being processed. When holding the
paint remover down, ensure that the low pressure
exerted is distributed evenly over the area of the
planing base.
8.2 Presenting the tool to the edge of a
workpiece
See diagram A: Hold the paint remover parallel with
the surface of the workpiece. When presenting the
tool, ensure that the planing base is in contact with
the largest possible area of the surface (10).
8.3 Operation
See diagram B: Guide the paint remover in such a
way that the planing base (10) is always positioned
on the surface that has not yet been processed. If
you proceed as shown, a narrow section is left over.
See figure C: You can remove this section by setting
the cutting depth to 0 mm (see section 7.3) and now
always guide the planing base (10) over the
processed surface.
8.4 Smoothing
Reduce the cutting depth to achieve a smooth
surface finish.
Danger of injury from the sharp edges of the
reversible blades. Effect maintenance work
only when the cutter head is idle! Switch off paint
remover and pull the mains plug from the socket!
Always wear personal protective equipment,
safety goggles, ear protectors, protective
gloves and heavy-duty footwear during work and for
all setting, conversion and maintenance tasks!
9.1 Cleaning the reversible blades
Paint might build up under the cutting edges of the
reversible blades. In this case, clean the edges of
the reversible blades using the graver (8).
9.2 Turn/replace the reversible blades
Use original Metabo reversible blades only.
Order no.: 6.31720 (4 pieces)
Order no.: 6.31660 (10 pieces)
Blunt edges of the reversible blades increase
the danger that the paint remover jams during
the milling operation and kicks back. Therefore turn/
replace blunt reversible blades in good time!
If required, clean Torx of the reversible blades using
a graver (8).
Axial reversible cutting plates:
Locking the cutter head.
8. Tips and Tricks
A
9. Maintenance
CB
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo LF 724 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo LF 724 S in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info