599620
10
Zoom out
Zoom in
Previous page
1/80
Next page
ENGLISHen
10
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash the protective clothing Do not
blow, beat or brush
See page 2.
1 Protective flap
2 Locking button
3 Additional handle
4 Sliding switch ( 0 / I )
5Handle
6 Extraction nozzle
7 Extraction connection piece (Ø 35 mm)
8Graver
9 Multi-socket spanner
a Hexagon
b Torx
10 Planing base
11 Reversible blade
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
6.1 Attaching the additional handle
Always work with the additional handle (3)
attached! Attach the auxiliary handle as
shown.
Always work with an extraction
system to guarantee perfect
machine operation.
Always guide the machine with both hands on
the handles (3), (5) provided.
7.1 Switching On and Off the paint remover
Switching on
Lift paint remover so that the cutter head is free.
Push the slide switch (4) forward.
I On
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Switching off
Lift paint remover so that the cutter head is free.
Press the rear of the slide switch (4). The slide
switch jumps back.
0 Off
Wait until the cutter head is at a standstill
before setting down the machine. An exposed
cutter head can get caught on the surface and lead
to a loss of control and possible serious injury.
7.2 Locking the cutter head
Danger of injury from the sharp edges of the
reversible blades. Lock the cutter head only
when the cutter head is idle! Switch off paint
remover and pull the mains plug from the socket!
Lay the paint remover on its side.
Press the locking button (2) up to the stop and keep
pressed.
Simultaneously turn the cutter head using the
hexagonal wrench (9-a) (any direction). Turn until
the pressed locking button noticeably engages and
the cutter head is locked.
7.3 Setting the axial cutting depth
Danger of injury from the sharp edges of the
reversible blades. Set the axial cutting depth
only when the cutter head is idle! Switch off paint
remover and pull the mains plug from the socket!
Lock the cutter head and keep the locking button
pressed.
5. Overview
6. Commissioning
7. Use
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo LF 724 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo LF 724 S in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info