595161
12
Zoom out
Zoom in
Previous page
1/88
Next page
ENGLISHen
12
Use a saw blade that is suitable for the material
being sawn.
Clean gummy or glue-contaminated saw
blades. Contaminated saw blades cause
increased friction, jamming of the saw blade and
increase the risk of back-kicks.
See page 2.
1 Speed preselection wheel*
2 Signal indicator*
3 Cable guide
4Guide plate
5 Scale (diagonal cut angle)
6 Locking screw (diagonal cuts)
7 Cutting indicator
8 Locking screw (parallel guide)
9 Parallel guide
10 Lever (for swivelling back the movable safety
guard)*
11 Locking button
12 Trigger
13 Connection piece
14 Lock nut (adjust saw disc angle)
15 Adjusting screw (adjust saw disc angle)
16 Depot for hexagon wrench
17 Locking screw (depth of cut)
18 Spindle locking button
19 Scale (depth of cut)
20 Marking (outer diameter of saw disc)
21 Inner saw disc flange
22 Saw disc
23 Outer saw disc flange
24 Saw disc fixing screw
25 Splitting wedge
26 Movable safety guard
27
Hex screw (splitting wedge setting)
* equipment-dependent
Before plugging in check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match with your power supply.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual
current of 30 mA or less.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
6.1 Setting the splitting wedge
The splitting wedge (25) prevents the wood from
closing behind the saw disc and jamming it while the
machine is in operation. This could otherwise lead
to recoiling.
The splitting wedge must be set in such a way
that the distance between its inner curve and
the toothed ring on the saw disc is no greater than 5
mm. Set the splitting wedge so that the lowest point
of the saw disc does not protrude by more than 5
mm below the bottom edge of the splitting wedge.
See illustration on page 3.
To adjust, loosen the hex screw (27), set the right
distances to the saw disc and tighten the hex screw
again.
6.2 Setting the depth of cut
Loosen the locking screw (17). Lift or lower the
motor unit up against the guide plate (4). Read the
depth of cut which has been set from the scale (19).
Tighten the locking screw (17) again.
It is advisable to set the depth of cut in such a way
that no more than half of each tooth on the saw disc
juts out under the workpiece. See figure on page 2.
The clamping force of the locking screw (17) is
adjustable. To adjust it, undo the lever screw.
Take off the lever and put it on offset in counter-
clockwise direction. Fasten with the screw. Ensure
that cutting depth adjustment moves freely when
the lever is open.
6.3 Slanting the saw disc for diagonal cuts
Loosen the locking screw (6). Tilt the motor unit
against the guide plate (4). Read the angle which
has been set from the scale (5). Retighten the
locking screws (6).
6.4 Correcting the saw disc angle
The
saw blade angle is set ex works.
If the saw disc is not at a right angle to the guide
plate at 0°: Loosen the locking screws (6). Loosen
the lock nut (14) and correct the saw disc angle by
means of the adjusting screw (15). Finally, retighten
the lock nut. Retighten the locking
screws (6).
6.5 Preselecting the speed (KSE 68 Plus)
Via the preselector wheel (1) preset the speed.
For recommended speeds see page 3.
6.6 Extraction connection piece / setting the
dust ejection
The connection piece (13) can be turned to the
desired position for extraction or sawdust ejection.
To do so, insert the connection piece up to the stop,
turn it and pull it back out. The connection piece can
be locked in 45° graduations.
Sawdust extraction:
connect a suitable dust extraction unit with suction
hose to the circular saw to extract the sawdust.
7.1 Switching on and off
To switch on: Push the locking button (11) in and
hold, then activate the trigger (12).
To switch off: Let go of the trigger (12).
7.2 Signal indicator (KSE 68 Plus)
The signal indicator (2) illuminates briefly upon
being switched on, signalling that it is ready to
operate. If the signal indicator illuminates during
5. Overview
6. Initial Operation, Setting
7. Use
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KS Partner Edition at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KS Partner Edition in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info