625642
11
Zoom out
Zoom in
Previous page
1/62
Next page
ENGLISH
11
ENG
8.4 Setting chisel position
The Chisel can be locked in 8 different positions.
Insert the chisel.
Press the lock (3) and hold in.
Turn the switch button (2) until it points upwards
(between position and ). Let go of the
lock.
Turn the chisel in the direction of the arrow until it
is in the desired position.
Press the lock (3) and hold in.
Turn the switch button (2) to position .
Release the lock (3) and check that the switch
button (2) has engaged.
Turn the chisel in the direction of the arrow until it
engages.
When a chisel is fitted, only operate the
machine in the chiselling operating
mode.
8.5 Setting impact force and speed
Turn the adjusting wheel (8) to the desired value.
The higher the number, the greater the speed and
the higher the impact force.
The correct setting is found by trial and error.
Example: if soft, brittle materials are being
chiselled, or cracking is to be kept to a minimum,
set the adjusting wheel to "1“ to "2“ (low impact
force).
For demolition or for drilling into harder materials,
set the adjusting wheel to the highest number
(max.power).
8.6 Switching On and Off
To switch on:
press the trigger switch (5).
To switch off:
release the trigger switch (5).
When working with the chisel hammer, only a
moderate amount of press-on pressure (approx.
20 kg) is required. High press-on pressure does
not increase work capacity and can possibly
shorten the service life of your tool.
In the case of deep bores, pull the drill bit out of the
bore from time to time in order to remove the stone
dust.
Motor cleaning: blow out the machine regularly
and thoroughly through the air slots with
compressed air.
Electronic signal indicator (6):
Rapid flashing - CODE! System
The tool was locked with a CODE! Key. The elec-
tronic anti-theft device is active. The tool can be
unlocked again with a CODE! key.
Slow flashing - carbon brushes worn (only KHE 75)
The carbon brushes are almost completely worn. If
the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorised service centre.
Continuous light - Service call-up
The tool cut out automatically. Bring the tool to a
Metabo Service Centre.
Rotational speed fluctuations:
High-energy, high-frequency interference can
cause rotational speed fluctuations up to the
maximum idling speed. The fluctuations disappear
again as soon as the interference fades away.
Use only genuine Metabo accessories.
If you need any accessories, check with your dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4:
A Extensive range of chisels for a wide variety of
applications.
B Special grease (for lubricating the tool shanks)
CCODE! key
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
These instructions are printed on chlorine-free
bleached paper.
9 Tips and Tricks
10 Maintenance
11 Troubleshooting
12 Accessories
13 Repairs
14 Environmental Protection
17026726_0107 KHE 75 KHE 55.book Seite 11 Freitag, 26. Januar 2007 8:42 08
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KHE 75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 75 in the language / languages: All languages as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info