625642
10
Zoom out
Zoom in
Previous page
1/62
Next page
10
ENGLISH
ENG
Always route the connecting cable away from the
tool towards the rear.
See page 3 (please unfold).
1 Tool lock
2 Switch button
3Lock
4 Rear handle
5 Trigger
6 Electronic signal indicator
7 Receiver of
Metabo CODE! Systems
(for use with
a
Metabo CODE! Key * )
8 Adjusting wheel for setting
impact force and speed
9 Additional handle
10
Hexagon ring
11
Wing nut
12 Depth stop
* not in scope of delivery
Smooth start:
The electronics system only increases impact
speeds slowly after switching on so that the chisel
or the drill retains the desired position on the
masonry. When the drill is inserted in an existing
hole, there are no jerks and jolts during start-up.
Electronic impact force and speed controller
Speed and impact frequency per minute can be
adjusted on the tool to match the application.
To reduce cracking when chiselling and drilling in
soft and brittle materials.
To produce an optimised tool setting for extremely
precise chiselling and drilling.
Turn-off carbon brushes
If the brushes are completely worn, the machine
switches off automatically.
Only KHE 75: An LED warns before the brushes
are completely worn.
Metabo CODE! System
Electronic anti-theft device at the push of a button.
With the CODE! key, which is available separately,
you can lock up your power tool and thus protect
it against misuse or theft.
Overload clutch
The overload clutch limits the maximum torque if
the tool should happen to block during operation.
This protects the gear unit and motor from over-
loading.
Before plugging in, check to see that the
rated mains voltage and mains
frequency, as stated on the rating label,
match with your power supply.
Use only extension cables with a min. cross-
section of 1.5 mm
2
. Extension cables must corre-
spond to the power consumption of the machine
(cf Technical Specifications). If a cable roller is
used, always roll up the cable completely.
7.1 Assembly of the additional handle
For safety reasons, always use the addi-
tional handle (9) supplied.
Release the additional handle by turning the
hexagon ring (10) counterclockwise. The addi-
tional handle can be moved to desired angle.
Tighten the hexagon ring (10) firmly.
The additional handle (9) must be firmly screwed
into the additional handle mount.
8.1 Depth Stop Setting
Release the wing nut (11). Set depth stop (12) to
the desired drilling depth and retighten wing nut.
8.2 Positioning, removing tool
Before inserting, clean tool shank and
apply supplied special grease (accesso-
ries: Order no. 6.31800)!
Use only SDS-max tools.
Positioning tool:
Turn tool and insert until it engages. The tool is
locked automatically.
Pull on the tool to check that it is
correctly seated.
(The tool must move a
few centimetres in axial direction.)
Removing the tool:
Pull tool lock (1) to the rear (a) in direction of arrow
and remove tool (b).
8.3 Setting operating mode
Press the lock (3) and hold in. Select the desired
operating mode by turning the switch button (2).
(Switch button must be horizontal). Release the
lock and check that the switch button has engaged.
Hammer drilling
Chiselling
5 Overview
6 Special Product Features
7 Commissioning
8Use
17026726_0107 KHE 75 KHE 55.book Seite 10 Freitag, 26. Januar 2007 8:42 08
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KHE 75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 75 in the language / languages: All languages as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info