625623
13
Zoom out
Zoom in
Previous page
1/92
Next page
ENGLISH
13
ENG
8.1 Depth Stop Setting
Loosen the additional handle (15). Set depth stop
(7) to the desired drilling depth and retighten addi-
tional handle.
8.2 Switching On and Off
To start the machine, press the trigger switch (12).
The speed can be changed using the trigger
switch.
The electronic soft start means that the machine
accelerates continuously up to the pre-selected
speed.
For continuous operation the trigger switch can be
locked using the lock button (11). To stop the
machine, press the trigger switch again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
8.3 Speed preselection
(only applies for UHE 28 Plus)
Preset the optimum speed for the application
using the adjusting wheel (8).
8.4 Operating mode selection
Select the desired operating mode by turning the
switch button (13). To turn, push in the lock (14).
Twist drilling 1st gear
(high torque)
Only applies for UHE 28 Plus
Twist drilling 2nd gear
(high speed)
Hammer drilling
(only with use of SDS
chuck) (2)
Chiselling
(only with use of SDS
chuck) (2)
In chiselling mode, the chisel is locked so that it
cannot turn. To position the chisel for a particular
application, set the switch button (13) between
and .
When a chisel is fitted, only operate the
machine in the chiselling operating mode
.
Avoid levering with the machine when a
chisel is fitted.
8.5 Selection of direction of rotation
Do not activate the direction switch (10)
unless the motor has completely stopped.
Selecting the direction of rotation:
R = Clockwise
L = Anticlockwise
8.6 Drill chuck change
When changing chucks, make sure that the
spindle is clean. Apply a light coating of
grease to the spindle. (for information on special
grease, see Accessories section: order no.
6.31800)
Only attach the Metabo chuck provided.
Removing the chuck:
Turn chuck lock (5) as far as it will go (a) in the
direction indicated by the arrow, and remove
chuck (b).
Replacing the chuck:
Place chuck onto spindle (6) (a). Turn chuck lock
(5) in the direction indicated by the arrow (b) until
chuck slides fully onto the spindle. Then release
the chuck lock.
Check to see that the chuck is properly seated.
8Use
b
a
b
a
17026909_0608 UHE KHE 28 Plus KHE Partner Edition.book Seite 13 Dienstag, 17. Juni 2008 3:51 15
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KHE 28 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 28 Plus in the language / languages: All languages as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info