625653
14
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISHen
14
1. Place the parallel guide/ripping fence (16) as
shown.
2. Screw knurled screw (15) into one of the
threaded holes.
3. Set the parallel guide/ripping fence (16) by
turning to the desired angle.
4. Firmly tighten the knurled screw (15).
Remove the battery pack from the machine /
pull the plug out of the socket before making
any adjustments, changing tools, carrying out
maintenance or cleaning.
Indexable inserts, holders for indexable
inserts, workpiece and chips can be hot after
work. Wear protective gloves.
Danger of crushing! Wear protective gloves.
7.1 Adjust scales (only when required)
The scales (12), (14) come with the correct settings
from the factory. However, should they be adjusted,
see chapter 9.3.
7.2 Set chamfer height
Read the set chamfer height
at the graduated
scale (12):
1. Read the set chamfer height at the graduated
scale (12). See illustration: Set chamfer height =
0.7 mm.
(The scale (14) is used for the rough orientation
during the setting process).
Change the chamfer height by turning the adjusting
ring:
2. Push the adjusting ring (13) downwards and
turn.
The chamfer height can be set in 0.1 mm (0.00394“)
steps. Each full rotation results in a change of the
chamfer height by 3.0 mm (1/8“).
Remove max. 3.0 mm per cutting operation.
Create larger chamfer heights in several
cutting operations. Do not exceed the maximum
permitted chamfer height (see chapter Technical
Specifications).
3. Carry out trial cut.
8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
Avoid unintentional start-up of the machine:
always switch off the machine, if the plug is
pulled from the mains socket or if there was a power
cut / if the battery pack was removed from the
machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Avoid the machine swirling up or taking in dust
and chips. After switching off the machine,
only place it down when the motor has come to a
standstill.
Machines with slide switch:
Switching on: Push the sliding switch (4) forward.
For continuous activation, now tilt downwards until
it engages.
Switching off: Press the rear end of the slide
switch (4) and release it.
8.2 Working Directions
1. Check indexable inserts (20). Change damaged
or worn indexable inserts.
2. Set the chamfer height (see section 7.2).
3. Always hold the machine with both hands on the
intended handles, take a secure stance and
concentrate on the work.
4. First switch on, then place the machine with the
support surface (17) onto the workpiece and
only then put the tool close to the workpiece.
5. When cutting, always work against the run of the
disc (see illustration). Otherwise there is the risk
of a kickback. Guide the machine evenly at a
speed suitable for the material being processed.
Do not tilt, apply excessive force or sway from
side to side.
6. Guide the machine in such a way that the parallel
guide (16) is in contact with the workpiece. If you
work without parallel guide: Guide the machine
in such a way that the ball-bearing stationary
seal ring (19) is in contact with the workpiece.
7. Setting
14
12
13
8. Use
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KFM 9-3 RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KFM 9-3 RF in the language / languages: All languages as an attachment in your email.

The manual is 10,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info