595419
14
Zoom out
Zoom in
Previous page
1/88
Next page
Sample applications for accessories:
Processing areas which are difficult to access
such as profiles, grooves and tight spaces is rapid
and simple with the special perforated base-plate.
This special base-plate can be fitted with a “cling-
fit” sanding sheet fitted to either its top or bottom
side. All “cling-fit” sanding sheets are available in
a grains of varying coarseness.
Use corundum “cling-fit” sanding sheets to sand
wood, metal, and paintwork, while processing
non-ferrous metals, stone, glass and varnished
surfaces calls for silicon carbide “cling-fit” sanding
sheets.
You can also sand metal, plastics and varnished
surfaces with silicon carbide-coated “cling-fit”
sanding sheets which provide a longer service life
than non-coated “cling-fit” sheets.
Use the “cling-fit” hard felt plate, the “cling-fit”
abrasive nylon web and the “cling-fit” nylon
cleaning web for polishing.
You can remove residual materials, such as the
foam from a carpet backing, traces of adhesives,
plaster and paint with scraper blades of varying
widths or by using the tool with the trowel.
9 Maintenance
Cleaning out the vacuum extraction channel
Clean out the dust extraction channel if it
becomes blocked and this adversely affects dust
extraction.
Remove the paper dust bag holder (9) or the
vacuum extraction nozzle (3), as appropriate.
Push a piece of wire approximately 20 cm long
(17) into the dust extraction channel (16) and clear
the blockage (18).
It may also be possible to clear the blockage (18)
by applying compressed air.
10 Troubleshooting
The “cling-fit” sanding sheet no longer
adheres to the base-plate.
Possible causes:
The “cling-fit” velcro surface on the base-plate is
dirty or worn.
Remedy:
Clean the base-plate (10) with a brush.
Replace the base-plate (10).
When being adjusted, the base-plate no longer
engages properly.
Possible causes:
The pocket holes in the base-plate are blocked.
Remedy:
Remove the base-plate (10) and tap to clear out
the pocket holes.
Insufficient suction force.
Possible cause (where the paper dust bag holder
is in use):
The dust filter is choked with dust.
Remedy:
Tap the dust filter to clear, or replace if necessary.
Further possible cause:
The dust extraction channel is blocked.
Remedy:
Hold the sander/scraper and tap it with your free
hand.
Connect up to an external suction unit and
vacuum free.
Clean the dust extraction channel, as described in
the section on maintenance.
11 Accessories
Use original Metabo accessories only.
Your Metabo dealer will supply you with any
accessories you may require.
To assist in selecting the correct accessories,
make sure that you take a note of the exact model
of your tool for your dealer.
Accessories available (page 4):
A Spare perforated velcro-faced base-plate
(as substitute)
B Spare special perforated base-plate with
self-adhesive, velcro-faced liner
C Spare self-adhesive, velcro-faced liner
(as substitute)
D Ready-punched “cling-fit” sanding sheets
(corundum or silicon carbide, various grains)
E “Cling-fit” abrasive nylon-web sanding sheets
F “Cling-fit” nylon cleaning web
ENGLISH
14
02_DSE_300_ENG_0410.qxp:02_DSE_300_ENG_0410.qxp 07.04.2010 15:45 Uhr Seite 14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo DSE 300 INTEC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo DSE 300 INTEC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info