595419
13
Zoom out
Zoom in
Previous page
1/88
Next page
Pull the base-plate (10) downwards.
At the same time, turn the base-plate (10) in the
desired direction.
Release the base-plate (10) or turn on until it
engages in position.
7.5 Removing and refitting the base-plate
Removing
Pull off the “cling-fit” sanding sheet.
Slacken off the hexagon socket-head screw (12)
with the hexagon socket-head key (6) and unscrew.
Remove the spring (11) from the recess in the
base-plate (10).
Remove the base-plate (10).
Refitting
Locate the base-plate (10) so that it engages in
position and cannot be turned.
Insert the spring (11) in the recess in the base-
plate (10).
Screw in and fully tighten the hexagon socket-
head screw (12) with the hexagon socket-head
key (6).
7.6 Removing and refitting the paper dust
bag holder
If you are not using an external suction unit but
are relying on your sander/scraper’s integrated
vacuum extraction feature, fit the paper dust bag
holder along with the dust filter and cover .
DSE 300: optional accessory
DSE 300 Intec: standard equipment
Removing
Press the catch hook on the paper dust bag
holder (9) and pull the dust bag holder out towards
the back.
Refitting
Push down the catch hook on the paper dust bag
holder (9) and push the cassette fully home until it
locks in position in the sander/scraper.
The catch hook must engage properly on the tool!
7.7 Changing the dust filter
Remove the paper dust bag holder (9).
Remove the cover (7).
Lift out the dust filter (8).
Push a new dust filter (8) into the paper dust bag
holder (9) far enough so that it no longer
protrudes.
Refit the cover (7).
Refit the paper dust bag holder (9).
7.8 Removing and refitting the vacuum
extraction nozzle
If you wish to use an external suction unit, fit the
vacuum extraction nozzle to the sander/scraper.
DSE 300: standard equipment
DSE 300 Intec: optional accessory
You can then connect a Metabo all-purpose
suction unit or some other suitable extraction
device to the vacuum extraction nozzle.
If you do not have a vacuum extraction device
fitted to the vacuum extraction nozzle (3), you
must locate the plug (5) to block off the extraction
channel.
Removing
Use the hexagon socket-head key (6) to slacken
off the hexagon socket-head screw (4) and
unscrew.
Pull the vacuum extraction nozzle (3) out towards
the back.
Refitting
Push the vacuum extraction nozzle (3) in from the
back until it is seated fully home in the
sander/scraper.
Use the hexagon socket-head key (6) to insert the
hexagon socket-head screw (4) and tighten fully.
8 Tips and Hints
Do not exert any great pressure as you guide the
sander/scraper over the surface to be processed.
Pressing harder does not increase the tool’s
performance.
Change worn “cling-fit” sanding sheets in good
time to ensure the desired results.
Change the dust filter at regular intervals to
ensure maximum dust extraction.
9
ENGLISH
13
02_DSE_300_ENG_0410.qxp:02_DSE_300_ENG_0410.qxp 07.04.2010 15:45 Uhr Seite 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo DSE 300 INTEC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo DSE 300 INTEC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info