511053
11
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH
11
ENG
8.2 Setting belt speed
The belt speed can be preset via the setting wheel
(12) and is infinitely variable.
Positions 1-6 correspond approximately to the
following belt speeds:
1......... 3.8 m/s 4 ........7.8 m/s
2......... 5.4 m/s 5 ........8.4 m/s
3......... 6.9 m/s 6 ........9.0 m/s
8.3 Sanding belt replacement
See illustration B, page 2.
- Manually loosen screw (5) and remove cover (3).
- Pull tensioner arm (7) backwards and remove
sanding belt (6).
- Place the new sanding belt on the rollers such
that its direction of circulation (arrows on the
inside of the sanding belt) matches the arrows (4)
on the cover. Place the sanding belt first on the
drive shaft and then on the roller on the sanding
attachment (1).
- Replace the cover (3) and tighten the screw (5) by
hand.
- Check the belt run and adjust if necessary (see
Section 8.4).
8.4 Adjusting belt run
Using the screw (2), adjust the sanding belt -
while the machine is not in operation and is
plugged out - so that it runs in the centre of the
sanding belt roller.
8.5 Sanding procedure
Switch the machine on first before mounting it on
the workpiece.
Place the machine on the material such that the
sanding belt is parallel to the surface of the work-
piece.
Keep the machine in constant motion because
otherwise recesses could be produced in the
material.
8.6 Replacing the sanding attachment
See illustration C, page 2.
- Removing the sanding belt (see Section 8.3).
- Remove screw (2), and remove sanding attach-
ment (1).
- Attach the other sanding attachment as shown
(ensure that the nose at the end of the sanding
attachment is pointing in the direction of the
tensioning arm, see illustration C).
- Secure with screw (2).
- Attaching the sanding belt (see Section 8.3).
- Adjusting the belt run (see Section 8.4).
Motor cleaning:
blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
For optimum operation: Sand on the side on which
the sanding belt moves towards the machine.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model of your
power tool in order to select the correct accessory.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
2
9 Cleaning, Maintenance
10 Tips and Tricks
11 Accessories
12 Repairs
13 Environmental Protection
17026977_0212 BFE 9-90.book Seite 11 Dienstag, 21. Februar 2012 11:51 11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BFE 9-90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BFE 9-90 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info