511053
10
Zoom out
Zoom in
Previous page
1/68
Next page
10
ENGLISH
ENG
Pull the plug out of the plug socket before any
adjustments, conversions or servicing are
performed.
The rated speed of the sanding belt must be at
least equal to the belt speed in idling marked on
the power tool. A sanding belt running faster than
its rated speed can break and fly apart.
Check prior to each use that the sanding belt is
correctly attached and is completely on the rollers.
Carry out a trial run: Allow the machine to run at
idling speed for 30 seconds in a safe location. Stop
immediately if significant vibrations occur or if
other defects are noted. If such a situation occurs,
check the machine to determine the cause.
See page 2.
1 Sanding attachment
2 Rotary knob for securing the sanding
attachment and adjusting the belt run
3Cover
4 Arrow (direction of rotation of
drive shaft
)
5 Screw for securing the
cover
6 Sanding belt
7 Tensioner arm for replacing the sanding belt
8 Sanding head
9
Locking screw for
adjusting sanding head
10 Additional handle
11 Sliding switch
12
Adjusting wheel for
setting belt speed
The machine is also available with different acces-
sory parts. An overview can be found on page 4.
Subject to change.
A Sanding belt arm
B Sanding belt, zirconia alumina
C Nylon web band
D Microfibre cloth
E Stainless steel cleaning spray
Before plugging in, check that the rated
mains voltage and mains frequency, as
stated on the rating label, match with your power
supply.
Attaching the additional handle
Always work with the additional handle
attached (10)! Attach the additional handle
on the left or right of the machine and secure.
Attach the additional handle to the side facing
away from the sanding belt (6).
Turning the sanding head (8) to operating posi-
tion
Loosen the locking screw (9) using the hexagon
spanner and, if necessary and depending on the
task at hand, turn the sanding head (8). The
sanding head must be positioned in the permitted
working area as shown (see illustration A, page 2).
Firmly tighten the locking screw (9).
Each time before you start work, verify that
the locking screw (9) is sufficiently tightened
to ensure that the sanding head (8) does not move.
Otherwise, the sanding belt (6) may come in
contact with the user. Loss of control can cause
personal injury.
8.1 On/Off switch, continuous activation
Always guide the machine with both hands.
Switch the machine on first before mounting
it on the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When
switching the machine on and off, keep it away
from dust deposits.
After switching off the machine, only place it
down when the motor has come to a stand-
still.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine using
the handles provided, stand in a safe position and
concentrate.
Switching on/
Continuous activation
:
Push slide
switch (11) forward. For continuous activa-
tion, now tilt downwards until it engages.
Switching off:
Press the rear end of the slide
switch (11) and release.
5Overview
6 Scope of delivery
7 Initial Operation
8Use
0
I
11
17026977_0212 BFE 9-90.book Seite 10 Dienstag, 21. Februar 2012 11:51 11
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BFE 9-90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BFE 9-90 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info