451400

Metabo BAS 500 Manual

11
Zoom out
Zoom in
Previous page
1/56
Next page
Saw Table Tilt
- For bevel cuts the table can be tilted up to 45°. Loosen
the wing nut (135) of the table trunnion assembly, tilt
the table to the required position and retighten the wing
nut. Make trial cut in a piece of scrap wood to verify
setting to desired angle.
- Hand guards:
Prior to tilting the two hand guards on the underside of
the table must be moved towards the fence guide
extrusion to clear the blade when the table is tilted.
7 Additional Information
For this band saw a range of optional accessories is
available. Both the band saw and the accessories are
only to be used for operations as described in this
manual or in the instructions supplied with the
accessories. Please contact your supplier or local agent
if you require additional technical information.
6 Safety Rules
1. Always disconnect from power when changing blades
or servicing the machine.
2. Before switching machine on be sure that all guards
are in place and securely locked.
3. Do not use cracked or bent saw blades.
4. Replace table inserts (24/79) if slot has enlarged.
5. For cutting operations with tilted table the rip fence
must be placed to the right of the blade.
6. When cutting round stock use a suitable jig to prevent
the work from turning.
7. When cutting boards in an upright position use a
suitable push block to prevent kickback.
8. Before tilting the table for bevel cuts replace the table
insert (79) with the wide slot table insert (24).
9. For safe operation and to keep dust emission within
the legal limits a dust collector with a minimum air flow
rate of 20 m/s must be connected to this band saw.
9 Optional Accessories
Crosscut and Mitre Fence
Stock-no. 090 901 8366
Circular Cutting Attachment
Stock-no. 090 901 8374
For cutting radii from 30 to 260 mm.
Belt Sanding Attachment
Stock-no. 090 900 5752
Quick and simple adaption of the belt sanding attachment
to the saw. For finishing the cut edge or deburring.
Because of the many different plastics available the
proper sanding belt speed must be found by testing.
Wheel Set
Stock-no. 090 900 0505
Fitting the wheel set to the machine makes the saw
mobile.
11
8 Connection to Power Mains
This appliance is safety earthed and must be connected
to an earthed outlet. It must be operated on a residual
current device (RCD) of 30 mA capacity.
Damaged power cables must be replaced immediately
by a qualified electrician. Risk of electric shock if
operated with a damaged power cable.
Children and juveniles should not to operate this machine.
This band saw is equipped with either a 1.1 kW 220-240
V single-phase or 1.5 kW 380-415 V three-phase motor.
For connection to power mains the power cable is fitted
with an earthed plug.
All models are equipped with an electronic brake. A light
humming sound emitted from the switch for a short
period after connection to power is normal and does not
indicate a fault. If the brake fails have the fine-wire fuse
inside the switch checked. The max. permissible number
of 20 switching actuations per hour should not be
exceeded.
For three-phase machines a 5-wire electrical installation
(3 phases, neutral and earth) is required. This applies for
extension cables as well. Check for correct direction of
rotation.
The electrical installation must ensure that a dust collector
starts up when this band saw is switched on (e.g. with an
induction coil in the supply lines).
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo BAS 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo BAS 500 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info