797762
6
Zoom out
Zoom in
Previous page
1/156
Next page
6
To extend the life of the unit, drain the condensed water from drain hole (8) before putting the unit into storage at the end of the
season.
DEVICE DESCRIPTION (pictures A and B)
1. Control panel 2. Cold air outlet 3. Signal receptor
4. Remote controller 5. Transport handle 6. Exhaust duct
7. Evaporator inlet 8. Drain plug 9. Air exhaust duct
10. Connector of air exhaust duct 11. Window exhaust adapter
CONTROL PANEL (picture C)
A. Power button B. Fan speed button
C. Mode button D. Timer / Temperature up button
E. Timer / Temperature down button F. Fan low speed indicator
G. Fan high speed indicator K. Cool mode indicator
L. Dehumidify mode indicator M. Fan mode indicator
N. Timer button R. WF – full water indicator
S. Set temperature / Timer display W. Timer indicator
REMOTE CONTROLLER – picture D
The remote controller transmits signals to signal receiver (3).
Button "A" - the appliance will be started when it is energized or will be stopped when it is in operation, if you press this button.
Button "C" - press it to select operation mode: "K", "L" or "M". Suitable indicator will be lighted up.
Button "B" - press it to select fan speed in sequence. Suitable indicator will be lighted up.
Button "D" / "E" - press to set up desired temperature in room or the timer. The display “S” present desired temperature, not present
temperature in room.
Button "N" - press to set the time of automatic off and automatic on.
OPERATION OF THE CONTROL PANEL
COOL / DEHUM / FAN
1. Turn on the device.
a) Connect the device and then the device beeps once.
b) Press the "A" button, then the device will turn on.
c) LED display indicates the set temperature.
2.Choose the operating mode
Press the "C" button to select the desired mode of operation by sequence:
Cooling mode "K" -> Drying mode "L" -> Fan mode "M.”
3. Adjust temperature
The temperature can be set within a range 16°-31°C. Press “D” or “E” button to increase or decrease the temperature by 1°C by
pressing once. The device LED panel shows the target temperature for 5 seconds and then displays the set temperature, not present
temperature in room.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mesko MS 7854 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mesko MS 7854 in the language / languages: All languages as an attachment in your email.

The manual is 19.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info