551340
18
Zoom out
Zoom in
Previous page
1/21
Next page
ENGLISH ENGLISH
14
15
InstallationInstallation
If you have more than one pair of WHDI DEVICE, each transmitter and receiver should
be at least 6.5 feet away from one another. If both the transmitter and the receiver exist
in the same room, the suggested the distance between the two is 6.5 feet minimum.
On Active mode, Press the POWER button on the top of Receiver or press RCU Power
button point to receiver, receiver enter Standby mode and transmitters HDMI out is
on. OSD displayed (3 sec. and then enter Standby mode).
On Active mode, Press the POWER button on the top of Transmitter or press RCU
Power button point to transmitter, both transmitter and receiver will enter Standby
mode. OSD displayed (3 sec. and then enter Standby mode).
Press the INFO button on the RCU, and Signal Quality, Source, Channel and resolution
will be displayed for user reference. OSD displayed (Press again for exit.)
Press the SOURCE button on the RCU or on the top of transmitter (or receiver) for
audio/video source input selection. OSD displayed
Press the IR button of RCU for change IR Blaster frequency, enable to switch IR Blaster
frequency 47K to 56K to 36K recurring. (Note : IR blaster frequency default setting is
47KHz). Press once for current IR frequency status display. The OSD shows:
Press IR key again to switch IR blaster frequency. The OSD shows
HDMI1 CH10 1280x1024
HDMI1 CH10 1280x1024
= OFF
1. On Screen Display (OSD) vs. RCU Instruction
1. Refer the drawing of the bottom page
that have relative position of the main
holes and attach this paper on wall.
ON
OFF
HDMI2 CH10 1280x1024
HDMI1 CH10 1280x1024
HDMI1 CH10 1280x1024
= 47KHz
= 56KHz
NOTE:
Only the status of the RECEIVER (receiver) connected to the HDTV can be displayed on
the OSD. The status of the TRANSMITTER (transmitter) HDMI out cannot be displayed.
Step 5: Mounting the devices to the wall
2. Drill pilot holes.
3. Insert the supplied two Anchors into
the wall.
4. Insert two screws into the anchors.
Leave 1/8” length for mounting the
Transmitter or receiver.
5. Place WHDI DEVICE main holes over
the protruding screws and slide down
into position.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Megasat Wireless HD Sender Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Megasat Wireless HD Sender Comfort in the language / languages: English, German as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info