551340
16
Zoom out
Zoom in
Previous page
1/21
Next page
ENGLISH ENGLISH
10
11
InstallationInstallation
Step 3: Setup the Blaster and IR Sensor Step 4: Boot up the Transmitter and Receiver
If necessary, connect the Infrared (IR) blaster (or sensor) Extender cable. Users can point
hand-held remote control of your High Definition AV equipment at the receiver or the
HDTV set to operate the source devices, not exceeding the distance of 66 feet at Line-
of-sight.
IR Blaster Extender cable
Stick IR Blaster to the front
of panel of Source device
1. Plug the IR blaster cable into the IR OUT jack of the transmitter.
2. Please try to manually move the IR blaster in the front of the front panel of your HD de-
vice and then press the key of remote control to search a good position of IR response.
Paste the IR blaster head near the front of IR sensor of your High-Definition audio/video
devices.
3. When the IR blaster cable is connected, it relays infrared command from your remote
control to the device. Users can control their AV devices by pointing their remote con-
trol to the receiver instead of to their AV equipment.
1. Place the two AAA batteries into the remote control.
NOTE:
1. The IR sensor supports 36KHz ~ 56KHz (NEC, RC5, RC6) remote’s signal protocol. There-
fore, it is possible that some devices may not be supported.
2. The IR blaster supports 47KHz remote’ signal protocol.
NOTE:
User can press POWER button of transmitter to turn off both transmitter & receiver simul-
taneously any time.
2. After the power cord is plugged into the electrical outlet, the device will be turned on
automatically.
3. If it is in Standby mode (Both POWER LED of transmitter and receiver are lit in red),
press the POWER button on both transmitter and receiver to turn on the transmitter
and the receiver.
4. If transmitters HDMI out display is on (Transmitter POWER LED is lit in blue) and recei-
ver stay in Standby mode (Receiver POWER LED is lit in red), press the POWER button of
receiver ONLY to wake up and make connection between transmitter and the receiver
for enable display out on receiver side.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Megasat Wireless HD Sender Comfort at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Megasat Wireless HD Sender Comfort in the language / languages: English, German as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info