790453

Medisana TT 205 Manual

4
Zoom out
Zoom in
Previous page
1/28
Next page
EN
EN Instructions for use
3-in-1-Electrotherapy device TT 205
Device and controls
IMPORTANT!
Failure to follow these instructions may
result in serious injury or damage to the
device.
WARNING
These warnings must be followed to
prevent possible injury to the user.
ATTENTION
These instructions must be followed to
prevent possible damage to the device.
NOTE
These instructions provide you with
useful additional information regarding
installation or operation.
Device classication: Type BF
Batch number
Information about protection against
foreign objects and water
Authorised EU representative
Manufacturer
Manufacture date
Legend
IP22
Press the On/O󰀨/M button 3 to exit the application. Pressing the On/O󰀨/M button 3 again for a long time
switches the device o󰀨.
The device has an automatic load detection at all set intensities above level 5.
If the electrodes do not stick to the skin properly or there is another connection problem, the device automatically
switches to level 0 and the “A” or “B” symbol ashes. The device then switches back to standby mode.
If the battery voltage is too low, the “Battery low” symbol z ashes. Stop the application and replace the batteries.
2460
EC REP
Troubleshooting
Use of the electrodes
• The electrodes supplied may only be used with the medisana 3-in-1 Electrotherapy device
TT 205. Make sure that the device is switched o󰀨 before applying and removing the elec-
trodes.
• If you want to reposition the electrodes during use, switch o󰀨 the device rst.
• Use of the electrodes can cause skin irritation. If you should notice this (e.g. red skin, blis-
tering or itching) stop the use. Do not use the electrodes regularly on the same skin areas.
• Never use the electrodes together with other people.
• The electrodes must be in full contact with the skin to avoid possible “hot spots”, which
can cause burns.
• Do not use the same electrodes more than 10 times because the connection to the skin
surface deteriorates with each use.
• The adhesive force of the electrodes depends on the skin properties, the storage condition
and the number of applications. If your electrode pads no longer stick completely to the
surface of the skin, replace them with new ones. After use, stick the electrode pads back
onto the protective lm and keep the electrodes in the storage bag so that they do not dry
out. As a result, the adhesive force is retained over a longer period of time.
• Clean and dry the skin areas where the electrodes are to be applied.
• Never remove the electrodes from the skin while the device is still in operation.
• Only use original electrodes that are recommended by the manufacturer. Other electrodes
could cause injuries.
• Each person reacts di󰀨erently to electrical nerve stimulation. There may be individual
deviations in the correct placement of the electrodes. Contact your doctor to nd out which
placement is best for you.
• Do not use electrodes smaller than the ones provided. Such use could make the current
density too high and cause injury.
• Do not change the electrode pads supplied, e.g. by cutting.
• Make sure that the area from which the pain originates is completely covered with the elec-
trode pads. In the case of painful muscle groups, all a󰀨ected muscles must be reached by
the electrodes.
NOTES on the TENS application
• If you nd the output intensity too strong, you can reduce it with the "-" button 8;
• As long as you feel comfortable during the application, continue it to the end. Pain im-
provement usually occurs after about 5 to 10 minutes;
• We recommend 1 to 2 applications per day for about 1 week;
• If there is no signicant improvement in pain after this time, contact your doctor.
NOTES on the EMS application
• Pay attention to the correct placement of the electrodes as described in these instructions;
• We recommend 1 to 2 applications per day for about 1 week;
• If you feel uncomfortable during the application, pause the application and/or reduce the
intensity.
Maintenance and cleaning
In order to ensure trouble-free and long-term functional reliability of the device, the following points should be
observed:
• Remove the electrodes from the device and clean the device with a soft, slightly damp cloth. In the case of
heavy soiling, you can also use a mild detergent.
• Protect the device from moisture. Do not hold the device under running water and do not immerse it in water
or other liquids.
• Do not place the device on hot surfaces and do not expose it to direct sunlight.
• Clean the surface of the electrode pads with a slightly damp cloth. Make sure that the device has been switched
o󰀨 beforehand!
• For hygienic reasons, each user should use their own electrode pads.
• Do not use aggressive substances or chemical cleaners to clean the device.
• Make sure that no liquid gets into the device. Do not use the device again until it is completely dry.
• Never clean the device during operation. Before cleaning, make sure that the device is switched o󰀨 and the
batteries have been removed!
Maintenance
• The manufacturer cannot be held responsible for damage caused by unauthorised repairs. If your device has
a technical problem, contact customer service.
• Do not try to carry out repairs yourself.
• Opening the device will render the warranty void.
• Your device was tested before being sold and does not require calibration or regular maintenance. If you have
any questions, please contact customer service.
Problem Possible causes Countermeasures
No display after changing the
battery
Batteries not inserted correctly or foreign objects in the
battery compartment.
Battery type may be wrong.
1. Check and clean the battery compartment.
2. Insert new batteries of the correct type. Pay attention to the
correct polarity!
No or too weak stimulation - Electrodes not placed correctly on the skin
- Connection to the device is not ideal
- Used batteries
- Too dry skin
1. Check that the electrodes are correctly attached to the skin and
that the cable connection to the device is optimum.
2. Replace the battery.
3. Wipe your skin and the electrodes with a damp cotton cloth.
The skin tickles or burns during
use
- The application is too long.
- Electrodes are not placed correctly on the skin or the
contact is not optimum
- The skin is hypersensitive
1. Use the device once a day and shorten the time of use.
2. Check that the electrodes are correctly attached to the skin.
3. Wipe your skin and the electrodes with a damp cotton cloth.
4. Consult your doctor if you have hypersensitive skin.
The device stops
during the application
- Electrodes are not placed correctly on the skin or the
contact is not optimum
- Used batteries
1. Check that the electrodes are correctly attached to the skin.
2. Replace the battery.
Program tables
Mode Body part Program Frequency Hz Impulse width µs Duration min. Waveform
TENS Neck 01 80-120 120-100 Standard: 30
Adjustable: 5-90 Modulation
02 4 150-200 Modulation
U1 Standard: 35
Adjustable: 2-100 Standard: 200
Adjustable: 100-300 Consistent
Shoulder 01 80-100 100 Modulation
02 2-60 260-160 Modulation
U1 Standard: 100
Adjustable: 2-100 Standard: 150
Adjustable: 100-300 Short
Pulse groups
Arm 01 2 250 Consistent
02 100 150 Short
Pulse groups
U1 Standard: 100
Adjustable: 2-100 Standard: 200
Adjustable: 100-300 Consistent
Hand 01 100 100 Consistent
02 2-10 200 Modulation
U1 Standard: 60
Adjustable: 2-100 Standard: 260
Adjustable: 100-300 Modulation
Back 01
60/50/45/10/50/35
200 Modulation
02 6/8/10 250 Modulation
U1 Standard: 55
Adjustable: 2-100 Standard: 200
Adjustable: 100-300 Modulation
Abdomen 01 80-120 120-100 Modulation
02 120 55 Consistent
U1 Standard: 80
Adjustable: 2-100 Standard: 100
Adjustable: 100-300 Consistent
Hips 01 100 150 Short
Pulse groups
02 40/6/50 200 Modulation
U1 Standard: 80
Adjustable: 2-100 Standard: 180
Adjustable: 100-300 Consistent
Leg 01 40/6/50 250 Modulation
02 80 150 Modulation
U1 Standard: 6–10
Adjustable: 2-100 Standard: 200
Adjustable: 100-300 Modulation
Foot 01 80-120 100-120 Modulation
02 2-10 200 Modulation
U1 Standard: 2-60
Adjustable: 2-100 Standard: 260-160
Adjustable: 100-300 Modulation
Joints 01 100 150 Short
Pulse groups
02 120 100-120 Modulation
U1 Standard: 80
Adjustable: 2-100 Standard: 180
Adjustable: 100-300 Consistent
EMS Neck 01 30 200 Synchronous
02 40 200 Synchronous
U1 Standard: 50
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Shoulder 01 45 200 Synchronous
02 55 200 Synchronous
U1 Standard: 80
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Arm 01 50 150 Synchronous
02 60 150 Synchronous
U1 Standard: 80
Adjustable: 20-100 Standard: 150
Adjustable: 100-300 Synchronous
Hand 01 4 200 Synchronous
02 5 300 Synchronous
U1 Standard: 20
Adjustable: 20-100 Standard: 150
Adjustable: 100-300 Synchronous
Back 01 60 200 Synchronous
02 70 200 Synchronous
U1 Standard: 80
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Abdomen 01 20 200 Synchronous
02 50 200 Synchronous
U1 Standard: 60
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Hips 01 30 150 Synchronous
02 60 150 Synchronous
U1 Standard: 40
Adjustable: 20-100 Standard: 150
Adjustable: 100-300 Synchronous
Leg 01 20 200 Synchronous
02 80 200 Synchronous
U1 Standard: 25
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Foot 01 4 200 Synchronous
02 5 300 Synchronous
U1 Standard: 20
Adjustable: 20-100 Standard: 200
Adjustable: 100-300 Synchronous
Massage Knead 01 28-44 120~250 30 Modulation
Rub 01 25-79 120~250 30 Modulation
Tap 01 49-97 100~240 30 Modulation
Technical information
Name and model:
Model no.
Power supply:
Channels:
Waveform:
Output current:
Intensity:
Output precision:
Application modes:
Number of programs:
Impulse width:
Frequency:
Application time:
Automatic switch o󰀨:
Operating conditions:
Storage conditions:
Dimensions approx.:
Size of electrode pads approx.:
Weight: approx.:
Item number:
EAN number:
medisana 3-in-1-Electrotherapy device TT 205
R-C4A
Li-Ion battery, 3.7 V
2
Biphasic rectangular pulse
Max. 120mA (at 500 Ohm load)
adjustable in 40 steps
± 20% for all parameters
TENS, EMS and MASSAGE
TENS: 30; EMS: 27; MASSAGE: 3
55 - 260 μs, depending on the program
2 – 120 Hz, depending on the program
5 - 90 minutes, adjustable depending on the program
after 1 minute
+5°C to +40°C at 15% to 93% rel. humidity:
atmospheric pressure 700 hPa to 1060 hPa
-10°C to +55°C at 10% to 95% rel. humidity:
atmospheric pressure 700 hPa to 1060 hPa
109 x 54.5 x 23 mm
50 x 50 mm
82 g
88348
4015588 88348 4
The current version of these user instructions can be found at www.medisana.com
In the interest of constant product improvement, we reserve the right to make technical and design changes.
Warranty and repair conditions
In case of warranty please contact your specialist shop or the service centre directly. Should you have to return
the device, please state the defect and enclose a copy of the purchase receipt or invoice.
The following warranty conditions apply:
1. medisana products are guaranteed for 3 years from the date of purchase. In case of a warranty claim, the
purchase receipt or invoice must be provided as proof of the purchase date.
2. Defects due to material or manufacturing defects will be remedied free of charge within the warranty period.
3. A warranty service does not extend the warranty period for either the device or for replaced components.
4. The following are excluded from the warranty:
a. All damage caused by improper handling, e.g. by not following the instructions for use.
b. Damage due to repair or intervention by the purchaser or unauthorised third parties.
c. Transport damage that has occurred on the way from the manufacturer to the consumer or when sending
it to the service centre.
d. Spare parts that are subject to normal wear and tear.
5. Liability for direct or indirect consequential damage caused by the device is also excluded when the damage
on the device is recognised as a warranty claim.
Shenzhen Roundwhale Technology Co., Ltd.
Add: 202, 2/F, Building 27, Dafa Industrial Park, longxi community,
longgang street, longgang district, Shenzhen, China.
Email: info@roovjoy.com
Shanghai International Holding Corp. GmbH (Europe)
Address: Ei󰀨estr. 80, 20537 Hamburg, GERMANY
Imported & distributed by:
medisana GmbH, Jagenbergstr. 19, 41468 NEUSS, GERMANY
The service address can be found on the separate attachment sheet.
EC REP
Device and controls
1
2
3
4
5
6
7
8
9
q
w
e
r
t
z
u
i
o
p
a
s
g f
d
h
0
Accessories
Cable set - Item number 88359
8 self-adhesive electrodes - Item number 88349
Storage
Switch o󰀨 the device and remove the cables. Place the electrodes on the carrier lm and pack them together with
the device and the cables in the original packaging.
Observe the storage conditions in the technical data!
Disposal
This device must not be disposed of together with household waste. Every consumer is legally
obligated to bring all used batteries, rechargeable or otherwise, whether they contain harmful sub-
stances or not, to a collection site in their town or city so that they can be transferred to the environ-
mentally friendly channels for disposal.
Contact your local authority or dealer regarding disposal.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medisana TT 205 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medisana TT 205 in the language / languages: All languages as an attachment in your email.

The manual is 2.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info