790487
15
Zoom out
Zoom in
Previous page
1/80
Next page
7
3 Operating GB
Overview of all buttons on the remote control (advanced functions):
t Button for manual selection of the massage method:
Switch through in the following order: Kneading, tapping, swedish,
shiatsu, clapping, roll massage, end function.
r + f + g (only with manually selected massage activated):
r Change the direction/rhythm of the massage
g Change the speed of the back massage in ve steps
f For tapping, clapping, shiatsu, roll massage: Change the distance bet-
ween the massage heads in 3 steps.
uspot massage/partial back massage:
Spot massage at the current point on the back.
Press the button again to switch to partial back massage.
z/d Up/Down: Adjust massage position individually
s Heating function
1. button press = activation at knee/leg
2. button press = activation at knee/leg + massage heads
3. button press = switch off the heating function
i Air pressure massage of the whole body (automatic mode): on/off
oManual selection of air pressure massage areas:
Leg support -> Arm support -> Shoulders -> Off
p Adjust the intensity of the air pressure massage in 5 steps
(works in automatic and manual mode)
a Switch foot massage roller on and off
3.4 Switching off the device
Press the Power button 9 on the remote control.
All functions are terminated - but the massage heads are still moving to
their parking position. Wait a few seconds.
Then set the on/off switch (position 7) to position „O“ and disconnect the
device from the power socket.
3.5 Troubleshooting
problem possible cause suggestion
The device does not
work
The device is not plug-
ged in properly
Ensure the voltage
on the device corre-
sponds to the local
mains voltage and
then plug in again.
Make sure the outlet is
properly working.
The device stopped
working
The device has just
nished its auto timer
session and has auto-
matically switched to
standby mode.
If you want another
session, press the
power button again.
The device stopped
working
You may have used
the device continuous-
ly for 45 minutes
where the over-heat
protection has been
activated.
Unplug the device and
let it cool down for 60
minutes before you
use it again.
The device stopped
working
An excessive load has
been applied on the
device.
Reduce the excessive
load and start again.
The device is abnor-
mally warm
The device is likely to
be overused.
Unplug the device and
let it cool down before
using it again.
Noise can be heard
from the device
Noise is made by the
mechanical parts of
the device.
This is normal and
does not mean that
the device is faulty.
If the problem encountered is not listed, please try the following suggestions:
1. Turn off the product and unplug it.
2. Wait for 60 minutes.
3. Plug the product back to the recommended outlet and restart.
4. If the problem persists, contact the authorized service center.
The service centre address is shown on the attached leaet.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Medisana MS 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Medisana MS 2000 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 4.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info