Manual Meade ETX-105AT (page 12 of 60) (English)

470208

Zoom out

Zoom in

1/60

GETTING STARTED

Fig. 5: Battery installation.

Fig. 6: Spread tripod legs.

Fig. 7: Slide spreader on rod.

Parts Listing

Getting the telescope ready for first observations requires only a few minutes. When

first opening the packing box, note carefully the following parts:

• The ETX Astro Telescope with fork mount system.

• #497 Autostar handbox with coil cord.

• One or more eyepieces, packed in plastic storage containers.

• Hex-wrench, packed with the instruction manual. See

MAINTENANCE,

page 45.

• #884 Deluxe Field Tripod; two attachment knobs; spreader tray with sepa-

rate spring, washers (2) and tension knob; leg extension lock knobs.

How to Assemble Your Telescope and Tripod

Assembly of the ETX telescope requires eight AA-size (user-supplied) batteries.

1. Remove the ETX telescope from its packaging and place it on a sturdy surface.

Place the ETX on its side and remove the battery compartment cover from the

underside of the drive base. Insert eight (user-supplied) AA-size batteries into the

battery compartment oriented as shown in the battery compartment. Replace the

cover and return the telescope to an upright position.

Caution: Use care to install batteries as indicated by the diagrams in the

battery compartment. Follow battery manufacturer's precautions. Do not

install batteries backwards or mix new and used batteries. Do not mix

battery types. If these precautions are not followed, batteries may

explode, catch fire or leak. Improperly installed batteries void your Meade

warranty. Always remove the batteries if they are not to be used for a long

period of time.

Note: Autostar does not require batteries; the telescope’s batteries

supply power to Autostar.

2. Assemble the #884 Deluxe Field Tripod:

Step a: Spread the tripod (1, Fig. 6) legs apart to a fully open position.

Step b: Slide the spreader tray (2, Fig. 7) onto the central threaded rod.

Step c: Slide a washer, followed by the spring, another washer and the

tension knob (3, Fig. 8) onto the threaded rod. Tighten the tension knob

to a firm feel.

Step d: Adjust the height of the tripod by loosening the leg lock knobs (4, Fig. 9)

and adjusting the height of the inner leg extensions. Then retighten the lock

knobs.

3. Mount your telescope in the altazimuth (alt/az) mode. If you wish to mount your

telescope in the equatorial mode, see EQUATORIAL ALIGNMENT, page 51.

Note: Throughout this manual, you will notice the term "Alt/Az," or more

properly, altazimuth.This term is frequently used to refer to altitude or the

up-and-down vertical movement of the telescope). Azimuth refers to the

side-to-side horizontal movement of the telescope.

Step e: Loosen the latitude control latch (6, Fig. 10) and lift up the tilt-plate (5, Fig.

10) so that you can easily access the underside of the plate. Relock the

latitude control latch, so the assembly doesn't slip while you are attaching

the telescope.

Step f: Line up the mounting hole (7, Fig. 11) on the base of the telescope

marked "High Latitude Leg" with the attachment knob (

8, Fig. 11) that is

closest to the latitude control bar (

9, Fig. 11). Line up the other

mounting hole with the attachment knob at the bottom of the tilt-plate.

Thread both attachment knobs into the base of the telescope. Tighten to

a firm feel only. (

See Fig. 12.)

Step g: Unlock the latitude control latch (10, Fig. 13) and lower the tilt-plate until

it is level (push the tilt-plate down until it stops; this is the level

position). Lock the latitude control latch.

Batteries

Cover

ᕡ

ᕢ

ᕤ

Fig. 8: Tension knob assembly.

Fig. 9: Adjust tripod height.

ᕣ

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Meade ETX-105AT in the language / languages: English as an attachment in your email.

The manual is 4,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Meade ETX-105AT Manual

Product: