643529
28
Zoom out
Zoom in
Previous page
1/42
Next page
Chapter 5
INSTALLATION AND USE MANUAL
page 28
Comfort air kit Technical service – MCZ Group S.p.A. all rights reserved - Reproduction prohibited
5.4. CONTROL UNIT
IMPORTANT!
All electrical connections must be performed by
qualified personnel in accordance with current laws in
each nation, using suitable equipment and in
compliance with the diagram indicated in this booklet.
All operations must be performed with the 230V 50 Hz
mains power cord disconnected.
Mcz shall not be held liable for damage to persons or
things due to incorrect connections or improper use of
the device.
5.4.1. Composition of control unit
The following material is provided with the control unit:
A. recessed box
B. Control unit, screws for fastening and power cord
C. Probe and cable clamp
D. Terminal for the common earth cable
E. Spare fuse (1.6 A)
F. Plate
G. Instructions
The control unit is equipped with 6 double terminals for the connection of:
1. Line (1-2 LINEA)
2. Fan 1 (3-4 VENTIL.)
3. Fan 2 (5-6 VENTIL.)
4. Light (7-8 AUX)
5. Switch for door opening (9-10 PORT.)
6. Probe (11-12 SONDA)
5.4.2. Positioning of the control unit
Make a hole in the wall (about 10X7.5 cm) for the installation of the
control unit, taking into account the positioning of the probe.
In this hole, insert the recessed box (A) without the control unit body
(B). Be sure to position it in a dry place, as far as possible from
heat sources, compatible with the position of the probe.
Run the cables (probe, power supply, fan and switch for door opening)
through the recessed box (A) so that they are available for connection.
Connect them to the terminals located on the control unit as shown in
figure 4.14.
Once connections are complete, insert the control unit body and fasten
it with the provided screws to the recessed box (A).
Finally, insert the white plate provided (F) or any other one, since the
control unit body is set up to house AVE SYSTEM 45 series and VIMAR
IDEA series plates using special hooks.
A
B
C
D
E
F
G
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Vivo 90 Wood at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Vivo 90 Wood in the language / languages: English as an attachment in your email.

The manual is 2,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info