643529
17
Zoom out
Zoom in
Previous page
1/42
Next page
Chapter 4
INSTALLATION AND USE MANUAL
page 17
Installation and assembly Technical service MCZ Group S.p.A. all rights reserved - Reproduction prohibited
A
A
E
E
E
F
E
D
C
C
C
B
4.3. EXTERNAL AND INTERNAL AIR INTAKE
4.3.1. Combustion air inlet
The VIVO fireplace stove has a rear hole Ø 100 with a flange for entry
of air that is indispensable for
combustion and proper operation.
This flange must be connected to the external air intake using
appropriate pipes (optional). The flange for ducting of the combustion
air intake normally faces the rear of the stove unit (as in the figure
alongside). However, it is possible to change its position and facing.
It is possible to remove the combustion air duct with flange Ø 100 and
to re-install it so that the flange faces downwards. This option is
provided to favour connection if the air flow or the ducts come from
under the fireplace stove.
To perform this operation (figure 4):
1. remove the frame by loosening the two screws (A) on the right
and the two on the left
2. loosen the 16 screws (B) at the upper part of the stove unit
and remove the cover
3. loosen the 6 screws (C) on the right and left sides and the
screw (D) on the back and remove the entire cladding
4. loosen the 6 screws (E) of the duct with the flange (F) Ø 100
5. turn the duct (F) so that the flange Ø 100 faces downwards
6. Perform the steps in points 1-2-3-4 in reverse order
In the absence of this direct connection (B), it is obligatory to
install in the room (preferably in the cladding) an external air
intake A with a free passage surface of not less than 150 cm
2
.
FOR BEST OPERATION, MCZ STRONGLY SUGGESTS
CONNECTING THE COMBUSTION AIR INTAKE Ø 100
TO AN EXTERNAL AIR INTAKE OF AT LEAST TO DRAW
AIR FROM OUTSIDE THE CLADDING.
4.3.2. Air inlet for natural ventilation
If the fireplace stove is installed with natural ventilation, you must
provide an external air intake B (150 cm²)
that allows natural fresh air
to flow inside of the cladding. This air intake A (150 cm²)
must be
made in the room where the stove unit is installed (figure 5).
It is indispensable to comply carefully with this
instruction, otherwise the lack of oxygen may
compromise the safety of the installation.
4.3.3. Air inlet for forced ventilation
If the fireplace stove is installed with forced ventilation, i.e. using the
COMFORT AIR kit, place air intakes and ducts as follows:
an external air intake (150 cm²) must be provided that allows
natural fresh air to flow into the cladding. This air intake A can also
be located in the room where the stove unit is installed.
Figure 5 – Intake for external combustion air
and for natural ventilation
A
B
Figure 4 – Removal of the combustion air
duct
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Vivo 90 Wood at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Vivo 90 Wood in the language / languages: English as an attachment in your email.

The manual is 2,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info