694358
26
Zoom out
Zoom in
Previous page
1/65
Next page
PELLET STOVES Chapter 3
INSTALLATION AND USE MANUAL
page 26
Installation and assembly Technical service - Rights reserved MCZ Group S.p.A. - Reproduction prohibited
In case of crossing walls built of flammable material, THE INSTALLER
MUST suitably insulate the pipe of the stove that crosses the walls,
using suitable insulating material (1.3-5 thick with a min. thermal
conductivity of 0.07 W/m°K).
A pipe which is inserted in the wall must be properly insulated so that it
does not lose heat and so that air outlet is silent.
You should use ducts of the same length so that the
air is evenly distributed. Otherwise, the air will tend
to flow through the shortest or least twisted ducts
In the example in figures 6 and 7 (front and rear view) the air duct is
an equal length totaling 8 meters, or in other words the pipes (B) will
have a length of approximately 4 meters each. In the case of ducts
with different lengths, the total must always be maximum 8 meters
(example 3 + 5 meters). In this case the heat will spread through the
rooms in an uneven manner.
The recirculation of air in the room occurs using the perforated sheet
metal placed in the rear of the stove C and the holes placed on the
metal sheet bottom
It is possible to choose the volume of air you wish to discharge from
the front part and from the rear part of the stove in an independent
manner, by adjusting the ventilation power directly with the remote
control.
3.4. INSTALLATION OF CERAMIC CLADDING FOR
SUITE AND CLUB
It is advisable to place small felt pads on the
ceramics where these touch the metallic parts of the
stove structure and in the contact between the
ceramic.
3.4.1. Assembly of the lower panel – Suite and Club Stoves
The stove is delivered with all the ceramics packed. Therefore, before
assembling the side tiles and the top, it is necessary to insert the lower
panel.
Proceed in the following way (fig.8):
Remove the micro-perforated sheet metal grill B on the right
side (handle side) on the upper part by removing the two
screws C.
Remove the screw D on the sheet metal E in a way that the
profile A is no longer locked.
At this point slightly lift the sheet metal E and remove the
profile A.
To remove the profile A lift it (sliding it from the base) and
tilt it slightly in a way that the plugs inserted on the base
come out.
Take the lower panel F and insert it from the right (handle
side) towards the left in a way that it enters exactly in the
housings
Reinsert the profile A making the plugs enter the case, and
lift the sheet metal E in a way to realign the profile “A”. Work
in a way that the upper plugs of the profile “A” are inserted
in the housings of the sheet metal “E.
Figure 6 – Front view of air outlet system
Figure 7 – Rear view of air outlet system
A
B
B
B B
A
Downloaded from www.Manualslib.com manuals search engine
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Musa Air 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Musa Air 2011 in the language / languages: English as an attachment in your email.

The manual is 4,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info