694165
40
Zoom out
Zoom in
Previous page
1/52
Next page
38
11-ALARMS
A12
The remote control has been out of the
reception range of the stove for over three
hours (or the batteries are at).
NOTE: only in this case, the stove does
not enter the shutdown stage due to an
alarm, and continues to work in the mode
set by the remote control via the last
command.
Move the remote control within the reception range
of the stove (or change the remote control batteries in
the event they are at). The alarm alerts will disappear
as soon as the appliance receives a new signal from
the remote control. A simple way of forcing signal
transmission to the stove is by pressing button B (which
changes the operating mode from manual to automatic
and vice versa).
A13
Overtemperature in the electronic control
unit.
The structure is too hot because the product has been
used for too long at the maximum power or due to poor
ventilation or because the air fans are faulty. When the
product is suciently cold, press button B on the control
panel or OFF on the remote control to cancel alarm A13.
Once the alarm is canceled, the product can be switched
on normally.
A14
Faulty air ow rate sensor This alarm does not block the stove, just a warning is
displayed. Contact an authorised service centre to have
the component replaced.
SER
Routine maintenance alert When this ashing message appears upon start-up
it indicates that the preset operating hours before
maintenance is due have elapsed and that an MCZ
qualied technician must be contacted for maintenance.
Exiting the alarm conditions
Follow the procedure described below to restore normal stove operation after an alarm has been triggered:
• Put selector D on the rear emergency panel on OFF for a few seconds, until the 3 digit alarm identity code disappears. The red LED
stops ashing and the sound signal is silenced by performing the steps below.
• Put selector D back in the REMOTE position, to control the operation of the stove via the remote control.
• Switch o the remote control and switch it on again if one wants to restart the stove.
Only if alarm A12 is triggered (no communication between the remote control and the stove), the stove stay on
according to the last mode set and automatically exits the alarm mode when the rst signal is received from the
remote control.
Downloaded from www.Manualslib.com manuals search engine
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for MCZ Cute Air 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of MCZ Cute Air 2016 in the language / languages: English as an attachment in your email.

The manual is 5,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of MCZ Cute Air 2016

MCZ Cute Air 2016 Additional guide - Dutch - 44 pages

MCZ Cute Air 2016 User Manual - Dutch - 56 pages

MCZ Cute Air 2016 Usermanual and installation guide - French - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info