Manual McCulloch Mac742 (page 12 of 17) (English, German, French, Spanish)

478387

Zoom out

Zoom in

1/17

Overcutting begins on thetop side of thelog

with the saw against the lo g. When overcut-

ting use light downward pressure.

Overcutting

Undercutting

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure. Hold saw firmly and maintain control.

The saw will tend to push back toward you.

WARNING: Never turn saw upside

down to undercut. The saw cannot be con-

trolled in this position.

First c ut on pressure side of log

Second cut

First c ut on pressure side of log

Second cut

BUCKING WITHOUT A

SUPPORT

S Overcut through 1/3 of the di ame ter of the

log.

S Roll the log over and finish with a second

overcut.

S Give special attention to logs under strain

to prevent the saw from pinching. Make

the first cut on the pressure side to relieve

the stress on the log.

BUCKING USING A L OG OR SUP-

PORT STAND

S Remember your first cut is always on the

pressure side of the log.

S Your first cut should extend

1/3 of the

diameter of the log.

S Finish with your second cut.

Cut

Usingalogforsupport

Cut

Using a support stan d

Cut

LIMBING AND PRUNING

WARNING: Be alert for and guard

against kickback. Do not allow the moving

chain to contact any other branched or objects

at the nose of the guide bar when limbing or

pruning. Allowing such contact can result in

serious injury .

WARNING: Neverclimbintoatreeto

limb or prune. Do not stand on ladders, plat-

forms, a log, or in any position which can cause

you to lose your balance or control of the saw .

IMPORTANT POINTS

S Watch out for springpoles. Use extreme

caution when cutting small size l imbs. Slen-

der material may catch the saw chain and be

whipped toward you or pull you off balance.

S Be alert for springback. Watch out for

branches that are bent or und er pressure.

Avoid being struck by the branch or the

saw when the tension in the wood fibers is

released.

S Keep a clear work area. Frequently clear

branches out of the way to avoid tripping

over them.

LIMBING

S Always limbatreeafter itis cut down. Only

then can limbing be done safely and prop-

erly.

S Leave the larger limbs underneath the

felled tree to support the tree as you work.

S Start at base of the felled tree and work to-

ward the top, cutting branches and lim bs.

Remove small limbs with one cut.

S Keep the tree between you and the chain

as much as possible.

S Remove larger, supporting branches with

thecutting techniques described inBUCK-

ING WITHOUT A SUPPORT.

S Always use an overcut to cut small and

freely hanging limbs. Undercutting could

cause limbs to fall and pinch saw .

PRUNING

WARNING: Limit pruning to limbs

shoulder height or below. Do not cut if

branches are higher than your shoulder .Get

a professional to do the job.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac742 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac742 Manual

Product: