Manual McCulloch Mac742 (page 11 of 17) (English, German, French, Spanish)

478387

Zoom out

Zoom in

1/17

Natural conditions that can cause a tree to

fall in a particular direction include:

S The wind direction and speed.

S The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de-

termine the direction of tree lean.

S Weight and branches on one side.

S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted,

it can snap and fall toward the operator.

Make sure there is enough room for the tree to

fall. Maintain a distance of

2-1/2 tree lengths

from the nearest person or other objects. En-

gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where cuts are to be

made.

Direction of Fall

45_

Plan a clear retreat path

FELLING LARGE TREES

(15cmindiameterorlarger)

The notch method is used to fell large trees.

A notch is cut on the side ofthe treein thede-

sired direction of fall. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTCH CUT AND FELLING THE

TREE

S Make notch cut by cutting the top of the

notch first. Cut through

1/3 of the diameter

ofthe tree. Next complete thenotch bycut-

ting the bottom of the notch. See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

Notch

First cut

Second cut

Final cut here. 5 cm above

center of notch.

5cm

S After removing the wood from the notch,

make the felling cut on the opposite side of

the notch. This is done by making a cut about

5 cm higher than the center of the notch.

This will leave enough uncut wood between

the felling cut and the notch to form a hinge.

This hinge will help prevent the tree from fall-

ing in the wrong direction.

Opening

of felling

cut

Closing

of notch

Hinge holds tree on stump and helps

control fall

NOTE: Before felling cut is complete, use

wedges to open the cut when necessary to

controlthedirection offall. Toavoidkickback

or chain damag e, use wood or plastic

wedges, but never steel or iron wedges.

S Bealerttosignsthatthetreeisreadytofall:

cracking sounds, widening of the felling cut,

or movement in the upper branches.

S As tree starts to fall, stop saw , put it down,

and get away quickly on your planned re-

treat path.

S DO NOT cut down a partially fallen tree with

your saw . Be extremely cautious with par-

tially fallen trees that may be poorly sup-

ported. When a tree doesn’t fall completely,

set the saw aside and pull down the tree with

a cable winch, block and tackle, or tractor.

CUTTING A F ALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen

tree to the desired log length.

WARNING: Do not stand on the log

being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill

of the log being cut.

Important points

S Cut only one log at a time.

S Cut shattered wood very carefully; sharp

pieces ofwoodcould beflung toward oper-

ator.

S Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

or foot.

S Do n ot cut in an area where logs, limbs,

and roots are tangled. Drag the logs into a

clear area before cutting b y pulling out ex-

posed and cleared logs first.

TYPES OF CUTTING USED FOR

BUCKING

WARNING: If saw becomes pinched

or hung in a log, don’t try t o force it out. You

can lose control of the saw r esulting in injury

and/or damage to the saw. Stop the saw ,

drive a wedge of plastic or wood into the cut

until the saw can beremoved easily. Restart

the saw and carefully reenter the cut. Do not

attempttorestartyour saw when it ispinched

or hung in a log.

Turn saw OFF and use a plastic or

wooden wedge to force cut open.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac742 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac742 Manual

Product: