Manual McCulloch Mac316XT (page 10 of 15) (English, German, French, Spanish)

478399

Zoom out

Zoom in

1/15

CUTTING METHODS

IMPORTANT POINTS

S Check chain tension before first use and af-

ter 1 minute of operation. See CHAIN TEN-

SION in the ASSEMBLY section.

S Cut wood only. Do not cut metal, plastics,

masonry , no n-wood b uildin g mat erials, etc.

S The bumper spike may be used as a pivot

when making a cut.

S Stop the saw if the chain strikes a foreign

object. Inspect thesaw and repair parts as

necessary.

S Keep the chain outof dirtand sand. Even a

small amount of dirt will quickly dull a chain

and increase the possibility of kickback.

S Practice cutting a few small logs using the

following techniques to get the “feel” of us-

ing your saw before you begin a major

sawing op eration.

S S queeze the throttle trigger and allow the

engine to reach full speed before cutting.

S Begin cutting with the saw frame

against the log.

S Keep the engine at full speed the entire

time you a re cutting.

S Allow the chain tocut for you. Exert only

light downward pressure.

S Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the saw at full

throttle without a cutting load, unneces-

sary wear can occur.

S To avoid losing control when cut is com-

plete, do not put pressure on saw at end

of cut.

S Stop the engine before setting the saw down.

TREE FELLING TECHNIQUES

WARNING:Do notcut near buildings

or electrical wires if you do not know the di-

rection of tree fall, at night since you will not

be able to see well, or during bad weather

such as rain, snow, or strong winds. as fall is

unpredictable.

Carefully plan your sawing operation in ad-

vance. You need a clear area all around the

tree so you can have secure footing. Check

for broken or dead branches which can fall

on you causing serious injury.

Natural conditions that can cause a tree to

fall in a particular direction include:

S The wind direction and speed.

S The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de-

termine the direction of tree lean.

S Weight and branches on one side.

S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted,

it can snap and fall toward the operator.

Make sure there is enough room for the tree to

fall. Maintain a distance of

2-1/2 tree lengths

from the nearest person or other objects. En-

gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, staples,

and wire from the tree where cuts are to be

made.

Direction of Fall

45_

Plan a clear retreat path

FELLING LARGE TREES

(15cmindiameterorlarger)

The notch method is used to fell large trees.

A notch is cut on the side of the tree in the de-

sired direction of fall. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTCH CUT AND FELLING THE

TREE

S Make notch cut by cutting the top of the

notch first. Cut through

1/3 of the diameter

of the tree. Next complete the notch by cut-

ting the bottom of the notch. See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

Notch

First cut

Second cut

Final cut here. 5 cm above

center of notch.

5cm

S After removing the wood from the notch,

make the felling cut on the opposite side of

the notch. This is done by making a cut about

two inches higher than the center of the

notch. This will leave enough uncut wood be-

tween the felling cut and the notch to form a

hinge. This hinge will help prevent the tree

from falling in the wrong direction.

Opening

of felling

cut

Closing

of notch

Hinge holds tree on stump and helps

control fall

NOTE: Before felling cut is complete, use

wedges to open the cut when necessary to

control thedirection offall. Toavoid kickback

or chain damage, use wood or plastic

wedges, but never steel or iron wedges.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac316XT in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac316XT Manual

Product: