Manual McCulloch Mac316XT (page 8 of 15) (English, German, French, Spanish)

478399

Zoom out

Zoom in

1/15

Adjusting

Screw

Chain Brake Nuts

Guide Bar

Adjusting Screw -- 1/4 T urn

S Lift up the tip of the bar and securely tight-

en th e chain brake nuts with the bar tool.

S Recheck chain tension.

Chain Brake

Nuts

WARNING: If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

WARNING: Muffler is very hot during

and after use. Do not touch the muffler or al-

low combustible material such as dry grass

or fuel to do so.

OPERATING YOUR UNIT

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Contact an

authorized service dealer.

BAR AND CHAIN LUB RICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar.

Only use Bar and Chain Oil for bar and chain

lubrication.

Oil Cap

Fuel mix cap

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

mixed with a good quality 2-cycle air-cooled

engine oil designed to be mixed at a ratio of

40:1. A 40:1 ratio is obtained by mixing 0,125

liter of oil with 5 liters of unleaded gasoline. DO

NOT USE automotive or boat oil. These oils

will cause engine damage. When mixing fuel

follow the instructions printed o n the container .

Always read and follow the safety rules relating

to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage. Acidic gas can damagethe fuel sys-

tem of an engine while in storage. To avoid

engine problems, empty the fuel system be-

fore storage for 30 days or longer. Drain the

gas tank, start the engine and let it run until

the fuel lines and carburetor are empty. Use

fresh fuel next season. Never u se engine or

carburetor cleaner products in the fuel tank

or permanent damage may occur.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling

the front hand guard back toward the front han-

dle as far as possible. The chain brake must

be disengaged before cutting with the saw.

WARNING: The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler. A hot

muffler can cause serious burns.

To stop the engine, move the ON/STOP

switch to the STOP position.

To start the engine, hold the saw firmly on

the ground as illustrated below. Make sure

the chain is free to turn without contacting

any object.

Hold saw firmly while pulling starter rope.

Use only 15″--- 1 8 ″ o

rope per pull.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full

extent of the rope as this can cause the rope to

break. Do not let starter rope snap back. Hold

the handle and let the rope rewind slowly.

For cold weather starting, start the unit at full

choke; allow the engine to warm up before

squeezing the throttle trigger.

NOTE: Do not cut material with the choke/fast

idle le ver at the FULL CHOKE position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Mac316XT in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Mac316XT Manual

Product: