684141

McCulloch Li58-52 M46R Manual

13
Zoom out
Zoom in
Previous page
1/320
Next page
regularly hose the grass catcher off with water and
let dry before using.
• Examine the grass catcher frequently for wear or
deterioration. Replace if necessary.
To examine the rear door
The rear door is attached between the rear wheels of
the product. The door decreases the risk of objects that
may be ejected in the direction of the mow position of
the operator.
1. Make sure that the rear door is not damaged.
2. Examine the rear door for defects that push the door
to close, including cracks or broken springs.
3. Replace the rear door or the springs if they are
damaged.
To sharpen and balance the blade
For best results, keep the blade sharp. Replace a bent
or damaged blade.
CAUTION: Use gloves, and/or wind the
blade with a heavy cloth, to prevent damage
to your hands .
1. Sharpen the blade with a file or on a grinding wheel.
Do not sharpen the blade when it is installed on the
product.
CAUTION: We do not recommend that
you sharpen the blade. If you do, make
sure that the blade is balanced. A blade
that is not balanced can cause damage
to the product or motor.
2. Put a straight nail in a piece of wood or a wall. Make
sure you can see 2-3 cm of the nail.
3. Put the center hole of the blade on the head of the
nail. If the blade is balanced, it must stay in a
horizontal position. If one of the two ends of the
blade moves down, sharpen the heavy end until the
blade is balanced.
To replace the blade
1. Lock the blade with a block of wood.(Fig. 55 )
2. Remove the blade bolt.
3. Remove the blade.
4. Examine the blade support and blade bolt to see if
there are damages.
5. Examine the motor shaft to make sure that it is not
bent.
6. When you attach the new blade, point the angled
ends of the blade in the direction of the cutting cover.
(Fig. 56 )
7. Make sure that the blade is aligned with the center of
the motor shaft.
8. Lock the blade with a block of wood. Attach the
spring washer and tighten the bolt and washer with a
torque of Nm.(Fig. 57 )
9. Pull the blade around by hand and make sure that it
turns freely.
WARNING: Use heavy duty gloves. The
blade is very sharp and cuts can easily
occur.
10. Start the product to do a test of the blade. If the
blade is not correctly attached, there is vibration in
the product or the cutting result is unsatisfactory.
Error codes
The error codes help you do troubleshooting on the
product and/or the battery pack while in operation.
LED screen Possible faults Possible steps
No LEDs come on after pressing
the power button on the user con-
trol interface, battery pack does not
function in product
Battery pack not fully put
into product or internal
fuse is blown
Push the battery pack fully into the powerhead un-
til a click is heard. If the LEDs do not illuminate af-
ter the battery pack has been fully put in and the
power button has been pressed on the user con-
trol interface, speak to an approved service cen-
ter.
All four battery capacity LEDs
flash, no other LEDs come on after
pressing the power button
Battery pack not fully put
into product or the internal
temperature of the battery
pack is too hot or too cold.
Push the battery pack fully into the powerhead un-
til a click is heard. If the LEDs continue to flash,
the internal temperature of the battery pack may
be too low or too high. Allow the battery pack to
warm up or cool. To increase the cooling process,
the battery pack can be inserted into the battery
charger to actively cool the battery pack.
778 - 004 - 23.10.2018 13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch Li58-52 M46R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Li58-52 M46R in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info