Manual McCulloch Li58-52 M46R (page 11 of 320) (All languages)

684141

Zoom out

Zoom in

1/320

2. Move the cutting height lever forward to decrease

the cutting height. (Fig. 47 )

OPERATION

WARNING: Read and understand the safety

chapter before you operate the product.

Basic cutting technique

• Always cut with a sharp blade for the best results. A

blade that is not sharp cuts unevenly and lets the

grass become yellow on the surface of the cut.

• Do not cut more than 1/3 of the length of the grass.

This specially applies during dry periods. Cut first

with the cutting height set high. Then examine the

result and lower to an applicable height. If the grass

is too long, operate slowly and cut two times if

necessary.

• For very heavy cutting, decrease the width of the cut

by making an overlap of the cut path and cutting

slowly.

• Cut in different directions each time to prevent

stripes in the lawn.

Before you start the mower

• Keep persons and animals away from the work area.

• Do daily maintenance. See

MAINTENANCE on page

To start the product

1. Put in the battery pack until you hear a click. Make

sure the battery pack is correctly installed. (Fig. 48 )

2. Put the key into the pocket below the battery lid.

Make sure the key is correctly installed. (Fig. 49 )

Note:

The key can only be put in one direction.

3. Press the power button one time. The button

illuminates fully. (Fig. 50 )

4. Pull the motor control handle in the direction of the

handlebar. The power button starts to flash. (Fig.

51 )

5. Press the flashing power button. The product then

starts. (Fig. 52 )

To stop the product

• Release the motor control handle on the product, or

press the power button one time. (Fig. 53 )

To use the drive on the wheels (if

equipped)

(Fig. 54 )

• Pull the drive bail in the direction of the handlebar.

• Before you pull the product rearward, disengage the

drive and push the product forward approximately

10 cm.

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To empty the grass catcher

1. Lift the grass catcher with the frame handle.

2. Remove grass clippings from the grass catcher from

below the handle.

3. Empty grass clippings from the bag with the frame

handle and the bag handle.

CAUTION: Do not drag the bag when you

empty the grass catcher to prevent wear.

To change the cutting mode

The product can be changed to one of three different

cutting modes while in operation by pressing the cutting

mode button.

• Auto mode - The product automatically adjusts the

cutting speed of the product in response to the

quantity of grass being cut.

•

Note: The product is set to Auto mode by default

while in operation.

• Boost mode - The product operates at high speed

regardless of the quantity of grass being cut.

• While the product is in operation, press the

cutting mode button one time to change from

Auto mode to Boost mode. The cutting mode

button then illuminates.

• ECO mode - The product operates at low speed

regardless of the quantity of grass being cut.

• While the product is in operation, press the

cutting mode button one time to change from

Boost mode to ECO mode. The cutting mode

button then illuminates and flashes.

• To go back to the default Auto mode, press the

cutting mode button one time while the product is

in operation. The cutting mode button then stops

flashing.

Note: If the motor control handle is released during

operation, the product stays in the current cutting mode.

If the product automatically stops, or the operator

presses the power button, the cutting mode used before

is erased from memory and the product starts in Auto

mode when started again.

778 - 004 - 23.10.2018 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch Li58-52 M46R in the language / languages: All languages as an attachment in your email.

The manual is 3,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

McCulloch Li58-52 M46R Manual

Product: