684234
9
Zoom out
Zoom in
Previous page
1/532
Next page
STARTING A COLD ENGINE
Follow these instructions to start your chainsaw. Your
chainsaw has a starting reminder decal similar to the
one shown below:
Make sure the chain brake is locked
before starting.
Press the primer (air purge) bulb
10 times. If fuel is not seen, press
the primer (air purge) bulb 10 more
times.
Note: If the outdoor temperature
is less than 4°C (40°F), press 15
times.
Unlock, then move the blue start
lever to the top (START) position.
Using your right hand, pull the
starter rope sharply until the
machine starts, or a maximum of
6 times.
Note: If the machine does not start
after 6 pulls, repeat the procedure
for starting a cold engine.
IMPORTANT: When pulling the starter rope, do not
use the full extent of the rope as this can cause the
rope to break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
Allow the engine to run for 30
seconds.
Before accelerating to full throttle,
pull the front hand guard towards
the front handle. The chain brake is
now unlocked.
Squeeze the throttle trigger for 10 seconds, then
release the throttle trigger to set normal idle. Your
chainsaw is now ready for use.
a WARNING: The chain must not move when the
engine runs at idle speed. If the chain moves
at idle speed refer to the MAINTENANCE
section for carburettor adjustment.
a WARNING: Avoid contact with the mufer. A
hot mufer can cause serious burns.
a WARNING: Do not attempt to throw or drop-
start the chain saw. Doing so will put the
operator at risk of serious injury due to loss of
control of the chain saw.
STARTING A WARM ENGINE
Make sure the chain brake is locked
before starting.
Press the primer (air purge) bulb
10 times.
Move the blue start lever to the top
(START) position.
Move the blue start lever to the
bottom (RUN) position.
Using your right hand, pull the
starter rope sharply until the
machine starts, or a maximum of
6 times.
Before accelerating to full throttle,
pull the front hand guard towards
the front handle. The chain brake is
now unlocked.
Squeeze the throttle trigger for 10 seconds, then
release the throttle trigger to set normal idle. Your
chainsaw is now ready for use.
DIFFICULT STARTING
(or starting a ooded engine)
NOTE: If the product does not start, the fuel can be
too hot.
NOTE: Always use new fuel and decrease the
operation time during warm weather.
1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the primer bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine.
STOPPING
To stop the engine push the STOP switch down.
a WARNING! To avoid involuntary start up,
the spark plug cap must always be removed
from the spark plug when the machine is
unsupervised.
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CS42STE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CS42STE in the language / languages: All languages as an attachment in your email.

The manual is 28,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info