684234
8
Zoom out
Zoom in
Previous page
1/532
Next page
FUEL HANDLING
FUELING ENGINE
a WARNING: Remove fuel cap slowly when
refueling.
IMPORTANT: This equipment is designed to operate
RQXQOHDGHGSHWUROZLWKDPLQLPXPRFWDQH520
with ethanol blended up to 10% maximum by volume
(%HIRUHRSHUDWLRQSHWUROPXVWEHPL[HGZLWK
a good quality synthetic 2-cycle air-cooled engine oil
designed to be mixed at a ratio of 50:1.
DO NOT USE automotive oil or marine oil. These oils
will cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is added to
petrol, shake container momentarily to assure that the
fuel is thoroughly mixed. Always read and follow the
safety rules relating to fuel before fueling your unit.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
CAUTION: Never use straight petrol in your unit.
This will cause permanent engine damage and void
the limited warranty. Do not use alternate fuels such
as ethanol blends above 10% by volume (E-15,
(RUDQ\PHWKDQROEOHQGHGIXHO8VHRIWKHVH
fuels can cause major engine performance and
durability problems.
Petrol, litre Two-stroke oil, litre
5 0,10
10 0,20
15 0,30
20 0,40
BAR AND CHAIN LUBRICATION
The bar and chain require continuous lubrication.
Lubrication is provided by the automatic oiler system
ZKHQWKHRLOWDQNLVNHSW¿OOHG/DFNRIRLOZLOOTXLFNO\
ruin the bar and chain.
Too little oil will cause overheating shown by smoke
coming from the chain and/or discoloration of the
bar. In freezing weather oil will thicken, making it
necessary to thin bar and chain oil with a small
DPRXQWWRRI'LHVHO)XHORUNHURVHQH%DU
DQGFKDLQRLOPXVWEHIUHHÀRZLQJIRUWKHRLOV\VWHPWR
pump enough oil for adequate lubrication.
Bar and chain oil is recommended to protect your unit
against excessive wear from heat and friction. If bar
and chain oil is not available, use a good grade SAE
30 oil.
Never use waste oil for bar and chain lubrication.
Always stop the engine before removing the oil cap.
STARTING AND STOPPING
PRE-OPERATION INSPECTION
Perform the following steps before every use of the
machine:
Check fuel mixture level
Check bar lubrication
Check chain sharpness
NOTE: Chain sharpening is a complicated task
that requires special tools. We recommend that
you refer chain sharpening to a professional chain
sharpener.
Check chain tension
Inspect and clean the guide bar
Check for damaged parts
Check for loose caps
Check for loose fasteners
Check for loose parts
Check for fuel and oil leaks
NOTE: It is normal for a small amount of oil to
appear under the saw after the engine stops. Do not
confuse this with a leaking oil tank.
STARTING POSITION
1. /D\WKHFKDLQVDZRQDÀDWVXUIDFH7KHFXWWLQJ
attachment must not be in contact with the
ground. Make sure the chain is free to turn without
contacting any object.
2. Lock the chain brake by pushing forward on the
handguard.
3. Place your left hand on the handlebar and your
right hand on the starter rope. Push your right foot
into the rear handle to stabilize the chainsaw.
4. Follow the starting instructions.
888
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CS42STE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CS42STE in the language / languages: All languages as an attachment in your email.

The manual is 28,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info