590546

McCulloch CABRIO 249-29CC Manual

12
Zoom out
Zoom in
Previous page
1/12
Next page
From time to time ensure all screws are tight.
Replace damaged, worn, cracked or warped
blades. Always make sure nylon string head or
blade have been assembled correctly (see
sections NYLON STRING HEAD and BLADE
ASSEMBLY) and blade fastener is tightened.
1) AIR FILTER CLEANING
(at least every 25 working hours).
A dust clogged air filter may cause carburetor
problems.
This may prevent the engine from reaching its
maximum speed and cause high fuel
consumption and/or difficult starting.
Remove filter cover as shown in figure 1.
Carefully clean the inside of filter box. The filter
can also be cleaned with compressed air.
2) SPARK PLUG
From time to time (at least every 50 hours)
remove and clean the spark plug and check
the electrode gap (0,5/0,6 mm.). Replace
spark plug about every 100 working hours or
whenever it is extremely encrusted. Heavily
encrusted electrodes can result from an
incorrect carburetor setting or from wrong fuel
mixture (too much oil in the petrol) or a poor
quality of oil in the fuel mix. Check and correct.
3) FUEL FILTER
To change fuel filter remove the tank cap and
pull out the filter with a piece of bent wire or
long forceps. Contact your Service Station for
general servicing and cleaning of internal parts
at least once a year.This will reduce the
possibility of unexpected problems and will
ensure maximum product life and efficiency.
REGULARLY: it is important, in order to avoid
engine overheating, to remove dust and dirt
from slots, gaps and from in between cylinder
fins using a wooden scraper.
LONG STORAGE: empty fuel tank and run
engine until dry.
Store trimmer in a dry place.
M. REGULAR MAINTENANCE
A
10
FAULT FINDING TABLE
Engine will
Engine runs badly The machine
not start
or looses power runs but does
when cutting not cut well
•
••
••
••
•
•
•
•
Engine still gives trouble: contact your dealer.
Check STOP switch is in the position I.
Control fuel level min. 25%tank capacity.
Check air filter is clean.
Remove spark plug, dry it, clean it and
adjust it, and replace it, if necessary.
Control and adjust the carburetor screws
if necessary.
Change fuel filter. Contact your dealer.
Carefully follow the cutting accessory
assembly instructions.
Check metal cutting accessory is sharp.
Otherwise, contact your dealer.
runs too fast, slowly turn screw ‘I’ or ‘T’ in an
anticlockwise direction until the correct speed is
obtained.
Precise numerical engine speed settings are
mentioned in the technical detail chart in the front
of the owner’s manual.
NOTE:
A)
Direct drive trimmers: The cutting head will
always rotate when engine is running.
B) All the above mentioned adjustments must be
made with the relevant cutting attachment
correctly fitted.
Warranty may be invalidated from incorrect
carburettor adjustment made by persons other
than an authorised dealer.
… 12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CABRIO 249-29CC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CABRIO 249-29CC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info