590546

McCulloch CABRIO 249-29CC Manual

11
Zoom out
Zoom in
Previous page
1/12
Next page
DANGER. Do not run engine without shaft
attached as clutch could fly off.
1) Insert the shaft (A) into the engine joint (B)
making the female squared end (C) inside the
joint mates with the male squared end (D) of
the shaft.
Rotate the shaft from right to left to obtain a
precise fit. Now tighten the locking bolt (E)
clockwise to ensure the shaft is held firmly in
the joint.
2) If the joint is not tightened onto the engine
housing, first make sure the shaft is fully and
correctly engaged up to the shank, then tighten
the 4 screws (A) in a criss-cross sequence.
3) Assemble the eyelet (A) of the ground wire
onto the end of the throttle cable and install the
washer (B).
Insert the throttle cable into the cable mount
(C), install the second washer (B) and insert the
hexagonal nut.
4) Fit the end of the trigger cable connector (B)
into the slot on swivel (C).
5)
Adjust the nut (D) of the trigger cable connector
so that the cable can easily slide in the opening
with a play of 1 mm before operating the swivel (C).
Tighten now the hexagonal nut (E).
6) Stop switch (STOP) cable: fit the connection.
G. ENGINE/SHAFT ASSEMBLY
9
A
J FRONT HANDLE
Secure the handle in front of the label placed on
the shaft 11 cm from the rear grip when
assembling nylon string head and 36 cm when
assembling metallic blades. This position ensures
optimum balance and safety. The handle must be
perpendicular to the shaft as illustrated.
H. HANDLE ASSEMBLY
I. STARTING AND STOPPING THE ENGINE
WARNING. First read sections: SAFETY RULES,
SAFETY USAGE and SYMBOLS.
COLD ENGINE STARTING
1) Move stop switch to the “ON” position.
2) Depress the safety lever (S), squeeze the
accelerator trigger (A) and push the throttle
advance forwards (B). Now release the
accelerator trigger (A) and then the throttle
advance (B).
WARNING: when the throttle advance is
engaged, the head or blade rotates.
3)
Move choke lever (E) to the closed position .
4) Press the primer bulb (C) several times until
you see fuel going back to carburetor through
pipe (D). Pull starter rope until engine fires once.
5) Move choke lever (E) to the open position
then pull starter rope until engine fires. Let
engine run for a few seconds holding the
trimmer. Now disengage throttle advance by
pulling trigger completely. Engine will now keep
on running at idle speed.
HOT ENGINE STARTING
STOP switch on START position I. Trigger on
idle position (released).
Choke towards (open position ). Press the
primer bulb (C) several times until you see fuel
going back to carburetor through pipe (D). Pull
starter rope.
WARNING: when the throttle (B) advance is
engaged, the head or blade rotates.
6) ENGINE STOPPING
Press the stop switch moving it to STOP
position 0.
WARNING: when the engine is switched off
rotating parts, blade or nylon string head, will
keep on rotating for a few seconds. Hold the
machine until all parts come to a standstill.
N.B. In an emergency the above mentioned
delay in stopping may be shortened by
touching blade parallel on the ground.
L. CARBURETTOR ADJUSTMENT
Your machine may be fitted with a highly
sensitive low emission carburettor. We now
therefore recommend that carburettor
adjustments are only made by an authorised
servicing dealer, equipped with instruments
that will ensure best performance with lowest
emission levels.
To adjust the idle speed, however, proceed as
follows:
With engine running and warm, slowly turn screw
‘I’ or ‘T’ clockwise until the engine runs smoothly
with a consistent noise level but without making
the chain or cutting head rotate.
If the cutting attachment does move or the engine
… 11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch CABRIO 249-29CC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch CABRIO 249-29CC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info