684266

McCulloch B428 PS Manual

7
Zoom out
Zoom in
Previous page
1/508
Next page
:KHQDGMXVWLQJWKH-EDUKDQGOHEHVXUHLWUHPDLQV
above the safety label and below the mark or arrow on
the shaft.
1. 3RVLWLRQWKH-EDUKDQGOHRQWKHVKDIW1RWHWKDW
the handle must be mounted between the two
arrows on the shaft.
2. Fit the screw, securing plate and wing nut as
shown.
3. 0DNHD¿QDODGMXVWPHQWRIWKH-EDUKDQGOHWRD
comfortable working position.
4. Tighten the wing nut.
ATTACHING THE HARNESS CLAMP
1. Place the upper harness clamp over the shaft and
position the lower harness clamp under the shaft.
Align the upper and lower clamp screw holes. The
clamp must be attached above the arrow on the
shaft.
2. Insert the two screws into the screw holes.
3. Secure the harness clamp by tightening the screws
with a hex wrench.
ATTACHING THE HARNESS
1. Insert your right arm and head through the harness
and allow it to rest on your left shoulder. Make sure
the harness hook is to the right side of your waist.
2. Adjust the harness, allowing the hook to be about
15 cm below the waist.
3. Fasten the harness to the harness clamp on the
shaft and lift the machine to the operating position.
4. 0DNHD¿QDODGMXVWPHQWVRWKDWWKHPDFKLQHLVLQ
a comfortable working position when it hangs from
the harness.
NOTE: It may be necessary to relocate the harness
clamp on the shaft for proper balancing of
machine.
5. Adjust the harness so that the cutting attachment
is parallel to the ground.
6. Let the cutting attachment rest lightly on the
ground. If you use a grass blade, it should balance
about 10 cm above the ground to prevent contact
with stones and the like. Adjust the position of the
harness clamp to balance the machine correctly.
CUTTING EQUIPMENT SELECTION
AND ATTACHMENT
a WARNING: Never use a cutting attachment
without an approved shield. Attaching an
incorrect or faulty shield can cause serious
personal injury.
CUTTING EQUIPMENT SELECTION
Use a grass blade to cut coarse grass.
Use a trimmer head to trim grass.
ATTACHING THE GRASS BLADE
1. Turn the bevel gear shaft until one of the holes in
the dust cup aligns with the corresponding hole in
the bevel gear.
2. Insert a small screwdriver in the hole to lock the
bevel gear shaft.
3. Place the blade and retaining washer onto the
shaft of the bevel gear.
a :$51,1*:KHQ¿WWLQJEODGHVLWLV
extremely important that the raised section
on the retaining washer engages correctly
in the centre hole of the blade. If the blade is
attached incorrectly, it can result in serious
and/or fatal personal injury.
4. Place the cupped washer onto the bevel gear
shaft with the cupped side of the washer toward
the blade.
5. Install the blade nut. Tighten the nut using a
wrench. Turn in the opposite direction to the
GLUHFWLRQRIURWDWLRQ7KHQXWKDVDOHIWKDQG
thread.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for McCulloch B428 PS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of McCulloch B428 PS in the language / languages: All languages as an attachment in your email.

The manual is 15,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info